ivr dialer

configuration mode) QuidwayConfig-if-Serial2) # ip address 10.139.184.253 255.255.255.255.252 configure the aux ip address 10.139.184.253. Note: the IP address of the remote Quidway R2501 router AUX port is 10.139.184.254 255.255.255.252) Ip route 10.138.185.192 route 192 10.139.184.246 Ip route 10.138.185.192 route 192 10.139.184.250 configure two static routes. In order to achieve load balancing, serial0 and serial1 have the same priority) Ip route 10.138.185.192 route 00000000192 10.139.184.

backup port configuration mode) Quidway (config-if-serial2) # ip address 10.139.184.253 255.255.255.255.252 (configure the aux ip address 10.139.184.253. Note: the IP address of the remote Quidway R2501 router aux port is 10.139.184.254 255.255.255.252) Ip route 10.138.185.192 route 192 10.139.184.246 Ip route 10.138.185.192 route 192 10.139.184.250 (configure two static routes. In order to achieve load balancing, serial0 and serial1 have the same priority) Ip route 10.138.185.192 route 000

) QuidwayConfig-if-Serial2) # ip address 10.139.184.253 255.255.255.255.252 configure the aux ip address 10.139.184.253. Note: the IP address of the remote Quidway R2501 router AUX port is 10.139.184.254 255.255.255.252) Ip route 10.138.185.192 route 192 10.139.184.246 Ip route 10.138.185.192 route 192 10.139.184.250 configure two static routes. In order to achieve load balancing, the priorities of serial0 and serial1 are the same.) ip route 10.138.185.192 255.255.255.192 10.139.184.254 preferen

Three-tier switch set PPPOE dial-up configuration PPPoE: 1. physical Interface: Enable PPPoE Association logic interface without IP address-if) # no ip add-if) # pppoe en-if) # pppoe-client dial-pool-number dialing pool number 2. logical interface: Create www.2cto.com-if) # int dialer No.-if) # ip add negotiated3. bind to PPP:-if) # encapusation ppp4. associate physical interface:-if) # dialer pool dialing

Part 3rd Infrastructure attacks Set the wireless card to "listening" status to identify which wireless network is active. With the help of "Aircrack-ng"-a wireless Network monitoring toolkit, the ability to intercept the 802.11 wireless network raw transmission data, especially good at intercepting the WEP initialization vector, to crack the WEP key. 7th. Remote connection and VoIP attacks1. The public switched telephone network has a modem connected to the critical device as a bac

) # network-number Router (config-If) # ^ ZConfigure the Novell IPX Routing Protocol: The Novell rip is updated once every 60 seconds.Router (config) # IPX routing [node address]Router (config) # IPX maximum-paths Router (config) # interface type PortRouter (config-If) # IPX network-number [encapsulation-type] [secondary] Router (config-If) # ^ ZConfigure DDR:Router (config) # dialer-List Group-number protocol-type permit [list ACL-number]Router (conf

PPP connection is established, and you can try:A. Run ifconfig, you will see Ppp0 network interface, this interface IP address is to the end of the server assigned to you IP address;B. Run route, you will find the IP address of the End-to-end server is added to the routing table;C.ping a remote host, should be able to connect.You can also run on another Virtual console:Tail-f/var/log/messagesAt this point, you can observe the dynamic PPPD log information.4 If you want to disconnect this connect

Desk.cpl on the Run command line, 3 will bring up the [show] Properties/Settings window. With it, when writing your own program, even the simplest batch program, you can easily open [Control Panel] to complete the system setup adjustment. This is much easier than the obscure RunDll32.exe. Cvtaplog.exe Disk Defragmenter assistant. Defrag.exe the defragmentation program. Run this program to eliminate disk fragmentation in the selected partition. Dialer.exe Phone

instant messaging and real-time network capabilities into applications without having to build a server-side hardware environment. Melting cloud for developers of the different scenarios required to provide a range of products, technology solutions, including: Client IM components, client IM infrastructure, service-side rest API, client real-time network communication Base library. With these solutions, developers can build instant messaging products directly in their applications, and can crea

1. Import library, the instruction is generally added to the stdafx.h #import "MSScript.ocx" No_namespace2. Create a Script object Script engineIscriptcontrolptr M_pscript;M_pscript.createinstance (__uuidof (ScriptControl));m_pscript->timeout = 1000 * ntimeout; Timeout settingM_pscript->putallowui (VARIANT_FALSE);M_pscript->putlanguage (_bstr_t (_t ("JScript")); 3. Read script files Wstring js = read_file ("C:/1.js");//read_file function omitted here 4. Add code and Execute Add codeM_pscript->

It is very useful to know some basic configuration statements about Cisco routers. The configuration can ensure the security and performance of our networks. Here we mainly analyze the basic configuration statements of Cisco routers. Cisco router basic configuration DDR:Router (config) # dialer-list Group-Number protocol Protocol-Type permit [list ACL-Number]Router (config) # interface bri 0Router (config-if) # di