juniper switch configuration

-gigabitethernet0/0/10]int g0/0/24[Sw1-gigabitethernet0/0/24]port Hybrid Tagged VLAN 10 20//Add interface to VLAN in tagged way[Sw1-gigabitethernet0/0/24]quit[Sw1]inter VLAN 10//Enter VLAN10[SW1-VLANIF10]IP Address 192.168.10.1 24//Configure VLAN10 member's Gateway[SW1-VLANIF10]DHCP Select interface//apply DHCP to the interface[Sw1-vlanif10]int VLAN 20[Sw1-vlanif20]ip Address 192.168.20.1 24[Sw1-vlanif20]dhcp Select interface[Sw1-vlanif20]int VLAN 100[Sw1-vlanif100]ip Address 192.168.100.10 24SW

Some things are not often forgotten. Remember to take a look at them when you are free and make progress together.H3C Configuration IP address and MAC address of the bound Interface [H3C-GigabitEthernet1/0/7] user-bind IP-address 172.162.20 Mac-address 001a-a0fc-72a2 Syslog output to the specified server (note that the switch time must be set to synchronize with the log server time)[H3C] Info-center en

Cisco switch QoS Speed limit configuration steps:1. Enable Global QoS2. Set the ACL matching traffic3. Set a class-map to match the ACL set in the second step4, set a Policy-map match Class-map, and then define a series of policies here, limit the bandwidth bitwise (BIT) for the calculation, burst in bytes (byte) calculation5, apply the POLICY-MAP to the corresponding interfaceMLS QoSIP Access-list Extended

The following is the author of the video course of a PPT course content, introduces the Huawei VRP System user Interface main configuration method, and a real Telnet remote login experiment to verify the correctness of these configurations. The video links for this course are as follows ( free to watch ): http://edu.51cto.com/lesson/id-22512.htmlFirst, the VRP user interface configuration steps650) this.wid

1. Experimental topology650) this.width=650; "Src=" https://s4.51cto.com/wyfs02/M00/97/B2/wKiom1kxPDizomXqAABw1vEUgaA990.jpg-wh_500x0-wm_ 3-wmp_4-s_3605733301.jpg "title=" rspan.jpg "alt=" Wkiom1kxpdizomxqaabw1veugaa990.jpg-wh_50 "/>2. Switch configuration4F-IDC-01 ConfigurationVLAN 100Remote-spanMonitor session 1 Source VLAN 13Monitor session 1 destination Remote VLAN 1004F-IDC-04 ConfigurationVLAN 100Remote-spanMonitor session 2 Destination interfac

Flexible QinQ configuration for the Huawei S8500 switch I. Simple introduction of the principle although common QinQ can solve VLAN expansion and simple L2 VPN functions, however, only a fixed outer TAG can be added to a port, which cannot meet the requirements of adding different outer VLAN tags to users of different services. For example, VLAN 100 ~ 200 for a business user, the outer label 10 is required;

filtered out.There are some other keys inside the Springboot to filter the classes that need to be loaded: Org.springframework.test.context.TestExecutionListener Org.springframework.beans.BeanInfoFactory Org.springframework.context.ApplicationContextInitializer Org.springframework.context.ApplicationListener Org.springframework.boot.SpringApplicationRunListener Org.springframework.boot.env.EnvironmentPostProcessor Org.springframework.boot.env.PropertySourceLoade

----------- --------------------------------------------------------GI1/0/1 Ip-mac INACTIVE-NO-SNOOPING-VLANGI1/0/2 Ip-mac Active Deny-all deny-all 24GI1/0/3 Ip-mac INACTIVE-NO-SNOOPING-VLANGI1/0/4 Ip-mac Active Deny-all deny-all 24GI1/0/5 Ip-mac Active Deny-all Deny-all 24GI1/0/6 Ip-mac Active deny-all deny-all 24GI1/0/7 ip-mac AC tive 172.16.24.150 a4:4c:c8:10:63:ee 24gi1/0/8 ip-mac INACTIVE-NO-SNOOPING-VLANGI1/0/9 Ip-mac Active Deny-all deny-all 24GI1/0/10 ip-mac IN

Vswitch Virtual Network (Virtual LANs) settings:VLAN division and external VLAN routing settings on Catalyst 5000Assign a VTP Domain)Add Cat5000 to the domainSpecify the relay port (a Trunk)Dynamic ISLAllocate VLAN to PortSet VLAN 20Configure the RouterNote: There are three VLANs, which are routed between VLANs through the Router.-Allocate VTP DomainsWhat is VTP?VTP is short for VLAN Trunk Protocol. It provides each device (router or LAN-switch) to se

Recently, servers in the data center always send packets externally. After detection, it was found that many ARP spoofing attacks are good. Before learning NP, I learned how to prevent ARP spoofing, in this way, the configuration to prevent ARP spoofing is published.Cisco protects against ARP spoofing and uses Port SecurityCisco port security has three processing modes in violation of security rules. There are two solutions.Three Processing modes:Shud

H3C switch typical access control list (ACL) configuration instance 1 networking requirements: 1. By configuring the basic access control list, you can achieve ~ Filter packets sent from hosts whose source IP address is 10.1.1.2 within; www.2cto.com 2. the Advanced Access Control List must be configured to prohibit mutual access between the R D department and the Technical Support Department, and restrict

TableSwitch>enableswitch>enableswitch#show Mac-address-tablemac Address Table-------------------------------------------Vlan Mac Address Type Ports----------------------------Configure the duplex mode and rate of the interfaceSwitch (config-if) #duplex {full | half | auto} Full: Specifies that the interface is fully duplex Half: Specifies the interface as half-duplex Auto: Specifies the interface as auto-negotiation Specifies the communication rate of the interfaceSwitch (

The previous two posts have explained how to back up the configuration file, the function of the expect script is to provide interaction, log in each switch to perform a backup command to copy it to the TFTP server. But in our normal work, the general backup method is to dis cu or sh run and then copy the information on the screen, in fact, the previous script can be slightly modified to use this method to

As an IT network siege lion, backup network equipment configuration is one of our daily work, but with the increase of equipment, previously very erasy manual backup, now also more and more time spent, Bo Master as an IT lazy people, believe there must be lazy way!Pre-Preparation: 1, NTP server 2, ftp/tftp server 3, command configuration1st: Time in the network is important, so you need NTP server to build NTP server with Windows Linux if you have an

Add acces to the VLAN:Sysint G0/0/1Port Link-type ACCPort default VLAN 2To add a trunk type to a VLAN:Sysint G0/0/1Port Link-type TrunkPort Trunk Allow-pass VLAN 2To create a single VLAN:SysVLAN 2Description XXXBatch Create VLAN:SysVLAN Batch 2 to 10Configure the traffic statistics feature for VLANs:VLAN 2Statistic enableThis article from the "Small Sky" blog, reproduced please contact the author!Some configuration commands about the VLAN of the Huawe

1. Experimental topology650) this.width=650; "src=" Http://s3.51cto.com/wyfs02/M00/78/7A/wKioL1Z9Z5jj_kkfAAA0zyZZNzI272.png "title=" N1. PNG "alt=" Wkiol1z9z5jj_kkfaaa0zyzznzi272.png "/>2. Experiment ConfigurationR2 ConfigurationInterface Vlan1IP address 192.168.137.20 255.255.255.0IP Route 0.0.0.0 0.0.0.0 192.168.137.1Clock timezone GMT +8NTP server 61.153.197.226NTP Master 1R1 ConfigurationInterface Vlan1IP address 192.168.137.10 255.255.255.0IP Route 0.0.0.0 0.0.0.0 192.168.137.1NTP server 19

Practical experience: routing Switch configuration document vlan200 and vlan201 are vlan ip subnet-zero ip routing www.2cto.com no ip domain-lookup spanning-tree mode pvst spanning-tree extend system-id spanning- tree vlan 200 priority 24576 spanning-tree vlan 201 priority 24576 spanning-tree vlan 202 priority 28672 spanning-tree vlan 203 priority 28672 spanning-tree vlan 204 priority 24576 spanning-tree vl

; Border: 1px solid # DDD; "alt =" spacer.gif "/> 650) This. width = 650; "width =" 554 "Height =" 408 "src ="/e/u261/themes/default/images/spacer.gif "style =" Background: URL ("/e/u261/lang/ZH-CN/images/localimage.png") No-repeat center; Border: 1px solid # DDD; "alt =" spacer.gif "/> Communication Verification 650) This. width = 650; "width =" 553 "Height =" 439 "src ="/e/u261/themes/default/images/spacer.gif "style =" Background: URL ("/e/u261/lang/ZH-CN/images/localimage.png") No-repeat