lync qos

First you have to turn on QoS in the QoS settings and set the overall uplink and downlink bandwidth. The second is set in the QoS unit, which is as follows: (content is the QoS rule help information, take a closer look to understand) you need to set the following entry: enable: Rule status. IP Address segment: The ad

All lab environments are deployed by Windows SERVER2012 Standard Edition Lync is based on the Microsoft AD domain, so the ad domain must be set up before deployment This is expected to prepare 9 virtual machines to deploy the service side 192.168.1.* for intranet network segment 10.9.0.* for outer network segment Here is a record of their own construction process, as far as possible to the required screenshots out, as far as possible, The relev

During Enterprise O M, we often find that the traffic increases in some cases when synchronizing data with some or the same server. To ensure the normal operation of the network, we can actually use the QOS provided by windows to limit the bandwidth used during synchronization. Here I will share the following operations: 1. Open the Group Policy on the server that needs to set QOS, start-run-gpedit. msc2.

Application descriptionPurpose: Enable NAT and QOS at the same time on AR1830. The data stream sent from PC1 is defined as 5 with a Gold priority. at least 50% of the ADSL bandwidth must be guaranteed; data Streams sent from PC2 are defined as multimedia (priority 3). At least 20% of the ADSL bandwidth must be guaranteed; Network Management (Priority 7) must ensure 10% of the bandwidth, but when the network is not busy,Each data stream can exceed the

Cisco's QoS speed limit and h3c a little difference, but overall, h3c of the comparison slag, the unit is not the same, the H3C car unit is KPBS, and the Cisco Police speed limit unit is bits per SECONDS,H3C this skipped. The theory of the token barrel is not verbose.Configure the QoS speed-limiting process on the ASA as follows:Steps:Step 1: Create ACLs to match streamsAccess-list rate_limit_lan-2 Extended

From: http://mybroadband.co.za/vb/archive/index.php/t-18042.html There are 4 commands used to set the QoS: At + cgeqminAt + cgeqreqAt + cgqminAt + cgqreq These commands set the QoS "window" that will be used to check ifConnection can be accepted. Let say you set the following QoS window: Min 64 K (d) 32 K (u)REQ 144 K (d) 64 K (u) The network will then accept th

Strictly speaking, cos and ToS are only a tag mechanism of QoS.The QoS range is too large, involving the marking and classification of the incoming data stream and the speed limit, the congestion avoidance and management of the network backbone, and the queue scheduling mechanism at the network egress.Cos indicates the priority of L2 isl or 802.1Q data frames. The value ranges from 0 to 7;TOS is the service type tag of layer-3 data packets, which is a

inter-frame encoding macro block. The intra-Frame Prediction macro block is not the same as the intra-frame encoding in H.263, the predicted intra-frame encoding method is more efficient than the non-predicted intra-frame encoding method, but it reduces the re-synchronization performance of intra-frame encoding, you can set the intra-Frame Prediction flag to restore this performance. (2) There are two types of clips that only contain intra-frame macro blocks, one is intra-frame (I slice), and t

There is a bit of crooked nuts on the forum sigh "Cisco router QoS project monitoring is always painful", admittedly, the general router traffic monitoring, using cacti to do, and due to the different upgrade version number, and the router iOS version is different, and very difficult, Some programs even need to TFTP download the written TCL script to the router operating system to perform, to cooperate with the retrieval.After 2 months of continuous g

In the process of enterprise operation and maintenance, often found with some servers or with some server data synchronization, you will find that some of the time the traffic will be larger, in order to ensure that the network is running, we can actually use the QoS of Windows to limit the use of synchronization bandwidth, here I share its operating methods: 1. Open the Group Policy above the server on which you need to set

Continue to the previous article9) Open the old Lync Server 2010 Standard Edition front-end server for Lync, tap topology Builder to create a new second site, and publish the topologies650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M00/74/77/wKioL1YeW--yXdrQAAG8EYpC0Es680.jpg "/>Right-click Lync Server 2010, New central site650) this.width=650; "src=" htt

SummaryThe UCMA full name is the Microsoft Unified Communications Managed API, which is used primarily to build middle-tier applications that work on Microsoft Lync Server. Developers can use the platform to build applications that provide access and control of Microsoft Lync Server enhanced presence information, instant messaging, telephony, video calls, and audio/video conferencing.Online statusSet the on