mbps to gbps

Parallel Optical Interconnection Technology Along with the digitization process, data processing, storage and transmission have developed rapidly. High bandwidth makes short-distance Interconnection a bottleneck for system development. Due to factors such as loss and Crosstalk, the transmission distance in the case of high bandwidth of copper wire-based electrical interconnection is limited, and the cost also increases. In addition, excessive cables will increase the system weight and wiring com

speed One of the biggest advantages of copper cables is reliability, which is measured by MTBF. The MTBF of a passive copper cable is about 500 million hours-generally an order of magnitude higher than the optical fiber industry standard. Copper cables provide a major benefit for enterprise data centers that are crucial to reliable data transmission: Avoid downtime. As data continues to increase and data is used for a wide range of applications, including drug discovery, traffic management, veh

Cisco mds9222i Fibre Switch most commonly used debug commands1. Check the switch portShow interface [Interface-range]View specified port run status, WWN information, configuration parameters, and packet statistics.Demonstration:mds9222i-1# Show Interface FC1/1FC1/1 is trunking-port FC1/1 operating normally, is a TE portHardware is Fibre Channel, SFP was short wave laser w/o OFC (SN)-Port, SFP hardware informationPort WWN is 20:01:00:05:73:ad:2a:00-switch port WWNPeer Port WWN is 20:01:00:05:73:a

wireless router, not by the wireless network card. Think about it from another angle. For example, there are two wireless routers A and B around the wireless network card, they use SSIDA and SSIDB to identify themselves. At this time, the wireless network adapter is connected by the SSID. Here we use the default SSID is the TP-LINK, of course you can change this parameter according to your preferences, to a combination of easy-to-remember numbers or letters or both. Channel: used to determine t

PHY reset845.814327 main [2237] ready ... 845.816526 Sender_body [1211] Start, FD 3 main_fd 3846.816691 main_thread [1720] 69.345 Kpps (69.424 kpkts 33.324 Mbps in 1001145 usec) 14.98 avg_batch 0 min_space847.268327 sender_body [1293] Drop copy847.817915 main_thread [1720] 69.176 Kpps (69.261 kpkts 33.245 Mbps in 1001229 usec) 14.98 avg_batch 99999 min_space848.819100 main_thread [1720] 65.934 Kpps (66.012

Wireless Access networks are widely used. There are wireless shadows in schools and cities. Here we will mainly introduce the speed of wireless access networks. How fast is the speed of Wireless Access networks? From 2 M of 802.11 to 802.11 M of 108g +, the speed of wireless access network equipment has been greatly improved in recent years, and it is almost the same as that of ordinary household 10/100 Mbps networks. However, we all know that, whethe

the wireless network card, they use ssid a and ssid B to identify themselves. At this time, the identifier of who is connected by the wireless network adapter is identified by the SSID. ◆ Here we use the default SSID is the TP-LINK, of course you can change this parameter according to your preferences, to a easily remembered number or letter or a combination of the two. Channel: used to determine the frequency range of the network. The value ranges from 1 to 13. The default value is 6. This par

From 2 M of 802.11 to 802.11 M of 108g +, the speed of wireless devices has been greatly improved over the past few years, and it is already similar to the 10/100 Mbps network for ordinary users. However, we all know that, whether it is 11 Mbps of 802.11b, 54 Mbps of 802.11g, or 802.11 Mbps of 108g +, It is a theoretic

distinguish different wireless routers to connect. This parameter is determined by the wireless router, not by the wireless network card. Think about it from another angle. For example, there are two wireless routers A and B around the wireless network card, they use ssid a and ssid B to identify themselves. At this time, the identifier of who is connected by the wireless network adapter is identified by the SSID. Here we use the default SSID is the TP-LINK, of course you can change this parame

your neighbor's house is deployed with a wireless network and the channel used is 6, in order to reduce the Wireless Interference between the two wireless routers, you can change this parameter to 1 or 13. ◆ Wireless route connection Setting Mode: this parameter is used to set the working mode of the wireless router. Two options are available: 54 Mbps (802.11g) and 11 Mbps (802.11b ), we do not need to mod

and the approximate disk space required to install the entire series: A basic Slackware system. (41.2 Mbps/102 MB)AP Linux application. (53.9 Mbps/161 MB)D program development tools. (78.7 Mbps/269 MB)E gnu Emacs (not installed ). (21.4 MB/74 MB)F Linux FAQ. (9.02 MB/34 MB)K Linux 2.4.31 kernel source code (not installed ). (37.6

consists of up to 12 frames. The output bit rate varies depending on the repeat frequency of the reference frame. The GOP structure varies with the bit rate. For example, when the bit rate is greater than 40 Mbps, the frame repetition mode is only I frame, and the GOP is the shortest, which has the advantage of high efficiency. When the bit rate is 15-40 Mbps, the frame repetition mode is IB, the GOP is sh

these clusters is approximately Gbps, which is approximately ten Gbps when the load peaks. Finally, I tried to make each server easily available with up to ten Gbps bandwidth, which is equal to a single server that can withstand 300,000 of users watching video streams at the same time. The existing FMS cluster contains more than 200 servers, I only need 15 units

, there is still no response. This phenomenon has lasted for two weeks. The website administrator ordered him to find out the cause within two days to solve the problem that the user could not click to shop. Otherwise ...... When did the fault occur? Generally, it is daytime and does not appear at night. When will the fault symptoms begin? There was no sign, and suddenly appeared and suddenly disappeared, very unstable and irregular. So how long has it been from the first fault to today? Only tw

Copyright. If you need to reprint, please keep the author and source information: http://blog.csdn.net/jmppok/article/details/38121115 During network transmission, the most important concern is the transmission efficiency. The most effective way to improve transmission efficiency is to compress the transmitted data. However, it takes a certain amount of time to compress data. Is it possible to improve efficiency after compression? How can we select an appropriate compression algorithm? Please r

Internet access in China has developed very rapidly. It may not matter if many people do not know about cable modem in Internet access. After reading this article, you must have gained a lot, I hope this article will teach you more things. When cable modem uses a cable TV network for high-speed access, the general connection mode is: one end is connected to a computer, and the other end is connected to a closed-circuit TV socket, and the CABLE MODEM is divided into two types by rate: symmetric r

dropped in the middle, and there was no client outside the room (10 meters away) as we expected) the performance is significantly lower than that of the client in the room. Because of the strong signal, the throughput between the five laptops and the file servers connected to the Mbps Ethernet interface is almost equal. Taking ASUS as an example, the total throughput of the five communication pairs reaches 25.405