eight ports at the same time, when the computer on the eight ports receives the broadcast information, it checks the information. if it finds that the information is sent to itself, it receives the information; otherwise, it ignores it. Because the information is sent from computer 1 to computer 8, computer 8 will eventually receive the information, this information is not received because it is not its own.
3. As the name suggests, a
1. Functions of the data link layer
Implements data error-free transmission. It receives raw data from the physical layer to form frames and bit groups) and transmits data between network devices. The frames contain the physical addresses of the active and target sites, the device that works on this layer has a switch
-2 switches with vrouters. layer-3 switches can control IP addresses, making it easier to build large-scale local area networks.3. Differences from centralized layer-3 core exchangeDistributed layer-
high speed non-blocking switching in the high port density condition, it is a wise choice to adopt the distributed third layer switch. Because the bus-type switch module can not avoid the conflict in the Ethernet environment, the matrix type avoids the conflict phenomenon of the port exchange. 3. Concern delay and de
computer 8. It broadcasts the information and sends the information to the eight ports at the same time, when the computer on the eight ports receives the broadcast information, it checks the information. if it finds that the information is sent to itself, it receives the information; otherwise, it ignores it. Because the information is sent from computer 1 to computer 8, computer 8 will eventually receive the information, this information is not received because it is not its own.
Router and three-layer switch experiment Demo--a gateway that acts as a two VLAN--Hundred dishes background : We know that routers have routing capabilities, so you know how to configure two gateways on a router interface (such as a two VLAN gateway)? Note that it is on one interface instead of two, and we sometimes use the three-layer
Three-layer Ethernet switch ip fdb table and its code example: How to filter incoming and outgoing packets in the access list when a three-layer Ethernet switch suffers from hardware processing problems in the following text, what about collecting evidence and contacting the security department or institution?
Hardware
Lab Requirements:The dual-core architecture combines three-layer switching technology with VTP, STP, and Ethernet channels to achieve high-speed network conversion, high availability, high reliability and redundant backup functions, mainly for the network of dual-core topologies.Experimental design:1. Configure VLANs on the switch to control broadcast traffic.2. Configure the Ethernetchannel between the 2 t
interface that will be configured as a three-tier interface
Step 3
No Switchport
To get the physical interface into layer three mode
Step 4
IP address ip_address subnet_mask
Configure IP addresses and subnet masks
Step 5
No shutdown
Step 6
End
Return Privileged Mode
Step 7
show interfaces [Interface-id]show IP inter
proven solution for this type of attack, based on several key technologies: Port Security FeatureDHCP snoopingDynamic ARP Inspection (DAI)IP Source Guard The following sections focus on the current very typical two-layer attack and spoofing how to combine and deploy the above technologies on a Cisco switch to prevent "man-in-the-middle" attacks, Mac/cam attacks, DHCP attacks, address spoofing, etc. i
Layer-3 switches are quite common, so I have studied the basic principles and design ideas of the layer-3 switches. I will share them with you here, hoping they will be useful to you. Based on the introduction of the three-layer switch
Preface:
It has been three months since the publication of the [Layer 2] in the blog series of "men are down to Layer 3, according to the previous visits and comments, many of my friends still like practical blog posts. After all, we are all called "siege lions", so we should check whether the "siege lions" are qualified and whether we can "build a house" instead
How to use a vro to connect different VLANs of a single-layer switch
Some simple configurations of the experiment
First configure PC
PC1 IP: 192.168.1.1 subnet mask: 255.255.255.0 Gateway: 192.168.1.254
PC2 IP: 192.168.1.2 subnet mask: 255.255.255.0 Gateway: 192.168.1.254
PC3 IP: 192.168.2.1 subnet mask: 255.255.255.0 Gateway: 192.168.2.254
PC4 IP: 192.168.2.2 subnet mask: 255.255.255.0 Gateway: 192.168.2.2
Transport Layer Flow control method
Data caching, window mechanisms and conflict avoidance.
The difference between a switch and a router
1) The switch works at the data link layer, the router works on the network layer;
2) The
Through the setting of flying Fish Star router, the network can be realized in 3 network segments of intranet. Suppose VE1260 a three-tier switch.
Through the setting of flying Fish Star router, the network can be realized in 3 network segments of intranet. Assuming that VE1260 a three-layer
Mention of the 4-7-tier switch users, the industry often think of ICP and ISP, but from 2003 onwards, the 4-7-tier switch user structure has begun to change, some enterprise users began to use such products. The 4-7-tier switch is a trend to marry.
Security issues to marry him
Many enterprise users from 03 began to pay attention to the 4-7-tier
In Photoshop, I drag multiple images onto a background, a lot of layers to switch in the layer panel to find the blurred, I remember before there can be directly on the map to switch to the current layer of the function, but I installed the PS after I forgot how to set up. I am photoshop CS2, thank you.
What are you t
Can a layer-3 Switch completely replace a router? This has always been the focus of debate. We can see that layer-3 switches are powerful, but only in a special environment can layer-3
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.