metric micrometer

addressesIP a flush dev eth1[[emailprotected] Desktop]# IP a1:lo: Remove all IPV4 IP addresses from the eth1Ip-4 a flush dev eth1[[emailprotected] Desktop]# IP a 1:lo: viewing network device informationIP link sh/show/l/list/lsIP link sh/show/l/ls/lsit eth1IP link sh/show/l/ls/list Dev eth1[[Email protected] Desktop]# IP link l1:lo: Stop and activate network devicesIP link set Dev eth1 downIP link set Dev eth1 up[[emailprotected] Desktop]# IP a1:lo: View the routing tableIP r/ro/routeIP R/ro/ro

inaccessible. Every 30 seconds, the distance vector routing protocol sends the entire route selection table to the adjacent site to update the route selection table of the adjacent site. In this way, it can collect a list of networks from other sites (directly connected or connected in other ways) for route selection. Distance Vector Routing uses the number of hops as the metric value to calculate the number of routers that need to pass to the destin

adjacent site within 9 0 seconds, the adjacent site is considered inaccessible. Every 30 seconds, the distance vector routing protocol sends the entire route selection table to the adjacent site to update the route selection table of the adjacent site. In this way, it can collect a list of networks from other sites (directly connected or connected in other ways) for route selection. Distance Vector Routing uses the number of hops as the metric value

routes, occupying excessive bandwidth. If the route selection table update is not received from the adjacent site within 9 0 seconds, the adjacent site is considered inaccessible. Every 30 seconds, the distance vector routing protocol sends the entire route selection table to the adjacent site to update the route selection table of the adjacent site. In this way, it can collect a list of networks from other sites (directly connected or connected in other ways) for route selection. Distance Vect

XP multi-Nic static route setting methodOne, multiple IPs are in the same network segment or VALN. There's nothing to say about this, but you can set the IP address, subnet mask, and default gateway in the local connection properties of each NIC.Two, multiple IPs belong to different network segment or VLAN. At this point, if you set the IP address in the usual way, fill in the subnet mask and default gateway of each network segment, you will find that the server is located in multiple network se

1. What is cube? A simple cube object consists of basic information, dimensions, and measurement value groups. The basic information includes the name, default measurement value, data source, and storage mode of the cube. A dimension is an actual dimension group used in a multi-dimensional dataset. All dimensions must be defined in the dimension set of the database before being referenced in the multidimensional data set. A measurement value group is a measurement value set in a multi-dimensiona

The original address; http://www.cnblogs.com/peida/archive/2013/03/05/2943698.htmlThe route command for the Linux system is used to display and manipulate the IP routing table (show/manipulate the IP routing table). To achieve communication between two different subnets, you need a router that is connected to two networks, or a gateway to two networks. In Linux systems, routing is usually done to address the problem that the Linux system has a gateway in a local area network that allows the mach

monitoring other systems Set an automatic alarm to notify you of sharp changes to a key indicator Configure NGINX To collect NGINX metrics, you must first make sure that the status module is enabled and a URL that reports the status metrics. For step-by-step configuration of open-source NGINX and NGINX Plus, see previous articles.Integrate Datadog and NGINX to install the Datadog agent The Datadog agent is an open-source software that collects and reports metrics of your host so that you can u

within 9 0 seconds, the adjacent site is considered inaccessible. Every 30 seconds, the distance vector routing protocol sends the entire route selection table to the adjacent site to update the route selection table of the adjacent site. In this way, it can collect a list of networks from other sites (directly connected or connected in other ways) for route selection. Distance Vector Routing uses the number of hops as the metric value to calculate t

1. Add a route table Route add 60.232.142.40 mask 255.255.255.248 192.168.100.250 Metric 3 if 2 Add a route record. All data packets destined for the 60.232.142.40/29 CIDR block go through the gateway of 192.168.100.250 through the interface card No. 2. The priority is 3. (What will happen ?) Route Add-P 60.232.142.40 mask 255.255.255.248 192.168.100.250 metric 3 if 2 It works the same as above, but it is a

only one data, OPENTSDB can only see one point.For OPENTSDB's own query interface, Access http://localhost:4242 can be.Data storage structure in the OPENTSDBLet's take a look at the important concept UID of opentsdb, starting with the data stored in HBase, let's look at what tables it has, and what those tables do.TSDB: Storing data pointshbase(main):003:0> scan ‘tsdb‘ROW COLUMN+CELL \x00\x00\x01U\x9C\xAEP\x00\x column=t:q\x80,timestamp=1436350142588, value=\x17 0

The route command in Linux is used to display and operate the IP route table (show/manipulatetheIProutingtable ). To achieve communication between two different subnets, you need a router that connects two networks or a gateway that is located in both networks. In Linux, routing is usually set to solve the following problems: the Linux system has a gateway in a LAN that allows machines to access the Internet, then you need to set the IP address of this machine to the default route of the Linux m