mmo for switch

Experiment on single-arm routing using a layer-3 Switch In the real environment, sometimes the gateway is not necessarily enabled on the router, sometimes the single-arm routing function is not necessarily connected to the interface on the router, you can use a layer-3 switch, because the vswitch itself has a variety of interfaces for flexible use, it is very common in practical work. Readers can compare th

* Vlan configuration ideas (access and Trunk) (1) create a Vlan and configure a static VLAN on an IOS-based switch: switch # vlandatabaseswitch (vlan) # vlanvlan-numnamevlan-nameswitch (vlan) # exitswitch # configureteriminalswitch (config) # interfaceinterfacemodu * Vlan configuration ideas (access and Trunk) (1) create a Vlan and configure a static VLAN on the IOS-based

With the increasing popularity of Mbit/s, Gbit/s, and even Mbit/s local area networks, broadband MAN networks and even broadband wide area networks are widely used. Whether it is Intranet, exclusive, or residential intelligent networks, it is increasingly expanding to massive amounts of information, it is forcing people to transmit audio, video, data and other information in the network system more and more demanding. With the rapid development of Internet, the use of e-commerce, e-government, e

The Cisco3550EMI switch is used as an instance of the DHCP server project, and the cisco3550emidhcp Configuration of Cisco3550EMI switch as an instance of DHCP server Engineering Network Environment: A 3550EMI switch is divided into three VLANs. vlan2 is the network where the server is located. It is named server, IP address segment is 192.168.2.0, subnet mask: 2

The following article is an effective description of the ethernet switch parameter configuration problem, the switch according to the work protocol layer can be divided into a second layer of switches, third-tier switches and layer fourth switch, according to whether or not to support the network management function can be divided into network-oriented

Absrtact: Spanning tree algorithms and protocols are the basis for automatically generating network topologies. This paper expounds the content of spanning tree algorithm and protocol, and gives the realization process in Ethernet switch. It is proved by practice that the square tip has a good effect on the analytic optimal topological structure of the network. The Ethernet switch must have routing capabil

the requirements of policy-based networking, advanced QoSQualityofService: service quality) and other service improvements. The huge market potential has greatly stimulated significant investment by manufacturers in key network equipment, so that in a very short period of time, the emergence of a traditional second-layer switch, to the Advanced Layer-3 Switch, to the latest layer-4 or even layer-7

Switch requirements 1. Switch to restore factory settings and its basic configuration. 1)//Enter privileged mode 2) del Config.text 2. Telnet mode to manage the switch. 1)//Enter the global configuration mode 2) enable password 0 [password] 3) Line 0 4 4) Password 0 [password] 5) Login 3. switch file backup,

Network Environment: A 3550EMI switch is divided into three VLANs. vlan2 is the network where the server is located and is named server. The IP address segment t-[/[Xm1S3 is 192.168.2.0, subnet mask: 255.255.255.0, Gateway: 192.168.2.1 the Domain Server is windows 2000 advanceserver and serves as a DNS server. The IP address is 192.168.2.10, vlan3 is the network where client 1 is located, the IP address segment is 192.168.3.0, The subnet mask is 255.2

As a very important transport hub in a LAN, a switch directly determines the stability of the LAN. Generally, when the quality of the switch is relatively good, the switch equipment is rarely prone to failures. Of course, this does not mean that the switch equipment can always work stably, with the passage of its "serv

Set the IP address of the Brocade switch. The default IP address of the Brocade switch is 10.77.77.77. In command line mode, you can use the ipaddrset command to set and modify the IP address of the switch www.2cto.com swd77: admin> ipaddrsetEthernet IP Address [10.77.77.77]: # enter the IP Address that the switch need

The configuration of a vswitch has always been mysterious, not only for general users, but also for the vast majority of network administrators. It is also an important and basic indicator for measuring the level of network management. This is mainly due to two reasons: first, the switches configured by the vast majority of enterprises are non-Network-connected vswitches on the desktop, and do not require any configuration at all. They are purely "Dummies". Like hubs, they are connected to the p

There are many things worth learning about the switch system. Here we mainly introduce how to reasonably configure the switch so that the switch system can control the network at will. With the rapid development of information technology, many organizations have established their own internal networks to cater to the information development trend, in the daily of

In a Cisco switch, how does one configure QOS speed limit? How to restrict BT download? This blog will use detailed examples for your explanation. Instance 1: QOS speed limit problem on CISCO switches It is used to control the bandwidth of a leased line user on a vswitch. The vswitch is usually at 10/100/1000 or three rates. QOS is required for other rates. You can also limit some ports, policy to restrict some ports. I. Network Description User‑pc1 i

Switch) performance directly affects the entire network. Therefore, it is not only necessary to understand the Switch parameters, but also helps you make better choices that meet your actual needs. Currently, the price of ATM switches remains high and is mainly used in backbone networks or wide area networks of large networks. Therefore, we will focus on Parameter Analysis of Ethernet switches.Selection of

Previous page Everyone talked about Cisco Basic Operation command switch, while dragon boat holiday, the Cisco simple switch configuration, and hope you share "Happy Dragon Boat Festival"! Ok, configure the switch, first, you must enter the global configuration mode switch, successfully connect the

Basic knowledge of VLAN division experiment: VLAN is short for Virtual Local Area Network (VLAN), which is a logical Network divided on a physical Network. This network corresponds to the L2 network of the ISO model. VLAN division is not limited by the actual physical location of the network port. A VLAN has the same attributes as a common physical network, except that it has no physical location restrictions. It is the same as a common LAN. Layer-2 unicast, broadcast, and multicast frames are f

The port of the core switch is mainly a fiber type, but the price of the switch fibre port is very expensive and requires special attention from the user, while the fibre port of the switch is not stacked and can only be used for cascading purposes. Cascading can use either a normal port or a special mdi-ii port. A pass-through cable should be used when the two

The layer-4 switch is quite common. So I studied the practical application of the layer-4 switch and shared it with you here. I hope it will be useful to you. With the increasing popularity of Mbit/s, Gbit/s, and even Mbit/s local area networks, broadband MAN networks and even broadband wide area networks are widely used. Whether it is Intranet, exclusive, or residential intelligent networks, it is increasi

The following article describes the parameter configuration of the Ethernet switch. The switch can be divided into Layer 2 switches, Layer 3 switches, and Layer 4 switches according to the working protocol layer, you can divide network-managed switches and non-managed switches based on whether the network management function is supported. Packet forwarding rate indicates the size of the packet forwarding ca