modem inventor

communication protocol operation. The MAC address is expressed in three bits, that is, eight devices can be addressable in one micro-network (the number of connected devices is actually unlimited, but only eight devices can be activated at the same time, one of them is primary, and seven are slave ). Figure 1 shows the topology of a Master/Slave Device in the micro-network. In addition, the Bluetooth system supports point-to-point communication to form a distributed network, that is, one master

Analysis of the problem: Why is the ADSL connection disconnected? Web pages cannot be opened, downloads are interrupted, or online video and audio streams are interrupted. These problems may cause many users to access the Internet through ADSL. However, when you carefully check the status of the adsl modem, you will find that the dial-up login is successful. So what exactly is the problem? How Should ADSL users troubleshoot? ADSL Network disconnection

save investment; it can enjoy ultra-high-speed network services to provide users with asymmetric upstream and downstream transmission bandwidth; it saves costs, you can call the Internet at the same time without affecting each other, and you do not need to pay additional phone fees when accessing the internet. The installation is simple, and you do not need to apply for additional lines. You only need to install an ADSL Modem on a common telephone li

provider) for advice, or you can make a quick decision with the way you purchased your router's previous network connection.There are several common ways to connect hardware:1, telephone line-> ADSL modem-> Computer2, twisted pair (Ethernet cable)-> computer3, cable TV (coaxial cable)-> Cable modem-> Computer4, optical fiber-> Photoelectric Converter-> proxy server-> PCADSL/VDSL PPPoE: A computer running a

Cause of failure This problem may occur if one of the following conditions is true: • Line noise is present on the telephone line connected to the modem. • The modem appears to behave abnormally. • A timing problem occurs between the computer and the modem. Warning: If you modify the registry incorrectly by using Registry Editor or other methods, you may have

At present, wireless router has become a home wireless sharing and Internet application of the mainstream, about the use of wireless router is also a lot of users are very interested in, we will pick some of the more representative of the wireless router problem, for you one by one to explain its fault solution, I hope you can analogy. The wireless router's red diagnostic or power light has been flashing. Wireless router does not work properly, how to solve? A: This is generally because the wi

The following is the ADSL Router installation on Datang Telecom A-400 to open the routing and UT Kang ADSL Router installation of detailed introduction, read the article today, you will be familiar with Datang Telecom A-400 to open the routing and UT Kang ADSL Router installation method. In the edit box, enter the Ethernet port IP address of the adsl modem. If this item is not changed during the first configuration or configuration, the default value

We should be familiar with PPP protocols, so here we will focus on the content of multiple PPP connection protocols. First, let's review the concept of PPP. The acronyms of Point-to-Point Protocol. A data link protocol used for dial-up telephone connection, for example, between a computer and the Internet. compared with SLIP (Serial Line Interface Protocol), PPP provides better protection for data integrity and security at the cost of additional costs. Do you think the speed of dial-up Internet

①. 1483B: refers to the 1483 bridging protocol. This function is implemented based on the Basic bridging protocol and on the first layer of the network physical layer, when this solution is used, the MODEM only acts as a bridge device and does not provide any protocol conversion or address filtering functions. Generally, after the MODEM can be synchronized with DSLAM and the VPI/VCI is set, basically, users

Specification entity (entityspecification) defines a certain type of entity; Characteristicspecification defines attributes of one or more types of entities; Characteristicspecvalue defines the possible values of feature types; You can define attributes for productspecification, product, and customer. So how can we apply Sid's "Specification mode" and "feature mode?2. Introduction of specification mode and feature Mode The following uses the most common product display page of an e-commerce

The first task is to drive the 3G Nic of China Telecom on a small board. The new thing is to run the network card on the PC first. The driver with the card is not available in Linux, so there are two ways to do that: Google: Is there a Linux open-source driver with the card; the other is to check whether the kernel itself can be supported. Later, it was confirmed that the USB-serial part of the kernel could be driven. This is a CDMA card, so I searched for something related to the CDMA