msp430 i2c

: USB hub foundHub 1-0: 1. 0: 2 ports DetectedMice: PS/2 mouse device common for all miceS3c24xx RTC, (c) maid ElectronicsS3c2410-i2c s3c2410-i2c: slave address 0x10S3c2410-i2c s3c2410-i2c: Bus frequency set to 390 kHzS3c2410-i2c s3c2410-

data (u0thr, u0rbr );Check the serial port status or wait for the serial port to be interrupted (u0lsr ). 21. Basic I2C operationsAnswer: The basic operation method of the I2C host is as follows:Set I2C pin connection;Set I2C clock rate (i2sclh, i2scll );Set as host, and send the start signal (i2en, Stas, and AA are 0

disk drives can work in parallel to improve the data transmission rate; thirdly, the verification technology improves the reliability: if one hard disk in the array is damaged, the original data on the damaged disk can be restored using other disks without affecting the normal operation of the system, the damaged hard disk (that is, the hot swapping function) can be replaced in the live state. The array controller automatically writes the restructured data to the new disk, or write a hot backup

" failed: "user" usbmon: debugfs is not availables3c2410-ohci s3c2410-ohci: s3c24xx OHCIs3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1s3c2410-ohci s3c2410-ohci: IRQ 42, Io mem 0x49000000usb usb1: configuration #1 chosen from 1 choicehub 1-0:1. 0: USB hub foundhub 1-0: 1. 0: 2 ports detectedmice: PS/2 mouse device common for all mices3c2440-i2c s3c2440-i2c s3c2440-

Interrupt. Otherwise, the External Interrupt can only be reflected in the extint register;To enable the device to enter the power-down mode and wake up through external interruptions, the software should correctly set the pin's external interrupt function before entering the power-down mode. 20. Basic uart0 operationsSet I/O to connect to uart0;Set the serial port baud rate (u0dlm, u0dll );Set the serial port working mode (u0lcr, u0fcr );Send or receive data (u0thr, u0rbr );Check the serial por

Linux View machine temperatureFirst, install the Lm_sensors[Email protected]_exercise ~]# yum-y Install lm_sensorsSecond, the configuration[Email protected]_exercise ~]# Sensors-detectWant to scan for them? This is totally safe. (yes/no): YESDoes want to scan for Super I/O sensors? (yes/no): YESThis is normally safe. Does want to scan for IPMI interfaces? (yes/no): YESDoes want to scan the ISA I/O ports? (yes/no): YESDoes want to probe the I2c/smbus a

demo: Drive DEMO:\KERNEL\DRIVERS\INPUT\TOUCHSCREEN\FT5X06_TS.C \kernel\drivers\input\touchscreen\ft5x06_ts.h DTSi file: \kernel\arch\arm\boot\dts\qcom\msm8x16-qrd.dtsi 2. Explanation of DTSi i2c@f9923000{//TP connected to the I²C registerfocaltech@38{compatible = "focaltech,5x06"; The content of the match is driven by i²cReg = Interrupt-parent = Interrupts = Vdd-supply = Vcc_i2c-supply = Focaltech,name = "ft6x06"; TP typeFocaltech,family-id = Focalte

how to debug camera on Qualcomm android from the perspective of the underlying driver, the architecture and Principles of the Qualcomm camera platform are not described too much.I. PreparationsFrom the project perspective, the software must be ready before the hardware (board) ready. From the perspective of the underlying driver, the software part can be divided into two parts: one is related to the Qualcomm platform, and the other is the sensor part, the common practice is to port the sensor-r

The first difference is of course the name:SPI (serial peripheral interface: serial peripheral interface );I2C (Inter IC Bus)UART (Universal Asynchronous Receiver Transmitter: Universal asynchronous transceiver)Second, the difference lies in the electrical signal line:The SPI bus consists of three signal lines: sclk, SDO, and SDI ). The SPI bus allows multiple SPI devices to connect to each other. The SPI device that provides the SPI serial clock is t

MSM8909 + Android5.1.1 keyboard driver --- sn7326 Introduction 1. Sn7326 Overview SN7326 is a keyboard extension chip with intelligent self-scanning, supporting up to 8x8 buttons. The press/release button action is encoded into a byte of data and stored in the key event register. The master controller can read the key event register through the I2C serial bus. SN7326 has the dejitter function. When any key is pressed, the interrupt output pin is set t

In the Linux drive, the following members are mainly included in the I²C system:I2C adapter 即I2C适配器I2C driver 某个I2C设备的设备驱动，可以以driver理解。I2C client 某个I2C设备的设备声明，可以以device理解。I²C Adapteris a CPU integrated or external I²C adapter, used to control a variety of i²c slave devices,

Two-wire serial bus developed by PhilipsGPIO analog I²c driver has its own set of transmission algorithms. Gpio analog i²c is to consume CPU resources, and the use of the I²C chip is not the CPU resources featuresFewer interface lines, simple control mode, small package form, high communication rate features a serial data line SDA, a serial clock line SCL It is a true multi-host bus, and if two or more hosts are initialized at the same time, data transmission can be prevented by conflict detecti