network routing tutorial

The following describes some experience and skills used in broadband routing. I hope this will be helpful for surfing the Internet. Only by forming good habits and correct configuration and maintenance of routers, in order to ensure the normal operation of the device and improve our Internet efficiency. Set the account to make sure the dial is successful During the actual use of the Broadband Router, we often encounter the phenomenon that we cannot su

pool name: 11 CIDR block, Bytes Enter the Default Gateway: 11.11.11.1 f0/0 ip address of the vro ), Bytes Enter the DNS server: 11.11.11.10, Bytes Enter the start IP Address: 11.11.11.2, Bytes Input subnet mask: 255.255.255.0 Bytes Click Add Bytes OK Manually configure the IP address of the PC Under S2: 10.10.10.10 Select the PC Under S1 to automatically obtain the IP address. The results are 11.11.11.2 and 11.11.11.3, respectively. Summary: 1. vswitch S2 Remote Management VLAN configuration,

Configure the rip dynamic routing protocol to connect the entire network. IP addresses 192.168.0.0/24R1 and R3: IP addresses 192.168.1.0/24R2 and IP addresses 192.168.2.0/24R3 and R4: IP addresses 192.168.3.0 /24 use the loopback interface to simulate lo 0 192.168.20.1/24R3 lo 0 192.168.30.1/24R4 lo 0 192.168.40.1/24 interface configuration of the internal client host R1 to omit R1router ripnetwork 192.168.

Ethernet channel:Switch (config) #interface range f0/x-X (x-x port selected)Switch (config-if-range) #switchport mode trunk (Configure Port to trunk mode)Switch (Config-if-range) #channel-group 1 mode on (open channel)Configure the DHCP service on the routerRouter (config) #Router (config) #ip DHCP pool Hydra (define an address pool)Router (dhcp-config) #network 192.168.1.0 255.255.255.0 (dynamically assigned IP address segment)Router (dhcp-config) #

Administrator mode cmdRouting Table Interpretationroute print -4Remove default settingsroute delete 0.0.0.0Outside the network, all the wireless, 192.168.0.1 for the wireless gatewayroute add 0.0.0.0 mask 0.0.0.0 192.168.0.1 –pInternal network by, all-in-wire, 192.168.12.1 for wired gatewaysroute add 192.168.0.0 mask 255.255.0.0 192.168.12.1 –p转自：https://zhuanlan.zhihu.com/p/22266906Windows

-interface=ens1--zone=internalInput Firewall-cmd--change-interface=ens3--zone=internalThe ens1 and ENS3 are configured as an intranet interface, but this is only temporary configuration, but also need to be added to permanently modify the intranet interface LAN, as when setting up an extranetInput Firewall-cmd--change-interface=ens1--zone=internal--permanentInput Firewall-cmd--change-interface=ens1--zone=internal--permanentAt this time ens1 and ENS3 will be configured as a permanent intranet, in

After the new switch is bought, all need to be simple configuration to meet the unit network operation, after the configuration of the device will need to put it where it should be placed, but in the future we need to view or modify this device, we need to use remote login to configure it. Let's talk about the specific configuration of remote login.First, you need to use a dedicated configuration line (console line) to connect the deviceSecond, config

Dial , the command is as follows:R1 (config) #int fa0/0R1 (config-if) #no IP addR1 (config-if) #no shR1 (config-if) #no shutdownR1 (config-if) #speed AutoR1 (config-if) #duplex AutoR1 (config-if) #pppoe enableR1 (config-if) #pppoe-client dial-pool-number 1R1 (config-if) #exitR1 (config) #7 , Configuration Logos Dial-up interface: commands are as follows:R1 (config) #interface dialer 1R1 (config-if) #mtu 1492R1 (config-if) #ip address negotiatedR1 (config-if) #ip Nat outsideR1 (config-if) #encap

A router is a layer-3 device that connects different subnets. Generally, a vro has a WAN port and a LAN port. Therefore, the corresponding vro has two addresses: one is the address of the same network segment as the LAN, and the other is the external address. The router must be used in pairs, that is, the LAN port of the router is connected to the host of the LAN, and the WAN port is connected to the outside router. When you access the Internet, you

[Web API series tutorial] 2.2-routing and Action Selection Mechanism in ASP. NET Web API This article describes how ASP. NET Web APIs route HTTP requests to specific actions on the controller. Note: For a high-level overview of Routing, see Routing in ASP. NET Web API. This article focuses on the details of the

Defaulthttpcontrollerselector chooses the controller type from this list. Iassembliesresolver Gets the list of project assemblies. The ihttpcontrollertyperesolverinterface uses this list to find the controller types. Ihttpcontrolleractivator Creates new controller instances. Ihttpactionselector Selects the action. Ihttpactioninvoker invokes the action. To provide your own implementation for any of these i

[Web API series tutorial] 2.1-Routing Mechanism in ASP. NET Web API This article describes how ASP. NET Web APIs send (route) HTTP requests to controllers. Note: If you are familiar with ASP. net mvc, you will find that Web API routing is very similar to MVC routing. The main difference is that Web APIs use HTTP method

? Routing (using Pika 0.9.8 python client) in the previous tutorial, we built a simple logging system. We can broadcast the log message to many recipients. in this tutorial, we'll add a feature to it-we'll make it possible to subscribe to only a subset of messages. For example, we will be able to only send a serious error message to the log file (saved to disk)

, and hardware cannot be separated. Because the architecture design takes into account the long-term operation, the stability is ensured. In addition, most of the important functions have been completed in the built-in system design, so there is little effort to set manual management, it can save time for technical or network administrators. However, if a certain hardware specification is not powerful and the scalability is not wide, it may fail to me

This article will give you a detailed account of the routing route to set the way, the following diagram shows the local area network routing between the routes: (the upper routing LAN port and the lower route LAN port is not covered) Upper-allied Routing settin

Http://blog.csdn.net/onil_chen/article/details/51758696?appinstall=0Today, let's talk about Ionic's routing configuration.Ask a lot of friends, because this content is more, so I always want to wait for me to learn more about the route of the tutorial.But some very simple also have friends do not understand, so I went ahead of this tutorial.Hope to be a little help to everyone, about my missing part, back to the t