Read about nexus switch configuration example, The latest news, videos, and discussion topics about nexus switch configuration example from alibabacloud.com
vswitch, just like a vro. In this mode, we can only view the current configuration, but cannot change the configuration, and the commands that can be used are very limited. Therefore, we must enter the privileged mode. Step 2: Enter the enable command in privileged mode in the previous step and enter the privileged mode. The command format is> enable. Then, enter the privileged mode prompt in
The h3c layer-3 Switch acl is an example of a new library that can only access the electronic reading room, and cannot access other hosts on the Intranet, so as to avoid security impact. the IP address of the On-Internet www.2cto.com electronic reading room is not opened to 10.0.1.9, the new library plans to divide vlan 11, network segment 10.1.11.0/25, and vlan-int 11 IP address 10.1.11.1. The layer-3
1. Configure an IP address on the router that is connected to the switch: for example, 192.168.1.1 242. Configure the following on the switch:[Switch]vlan 10[Switch-vlan10]quit[Switch]interface VLAN 10[
slots. The maximum number of switches that can be stacked in a stack unit. This parameter specifies the maximum port density available in a stack unit. The minimum/maximum number of 10 M Ethernet ports is the minimum/maximum number of 10 M Ethernet ports supported by an Ethernet switch. The minimum/maximum number of M Ethernet ports is the minimum/maximum number of M Ethernet ports supported by a switch. T
-value represents the N2 value in the range of 1 ~ 255.Default condition]The default value of LAPB parameter N2 is 5.Command mode]Interface Configuration ModeUser Guide]N2 indicates the maximum number of attempts by DCE or DTE to successfully send a frame to DTE or DCE.Example]Set the LAPB parameter N2 on the Serial0 interface to 20.Quidway (config-if-Serial0) # lapb n2 209. lapb t1Configure the LAPB system timer T1Lapb t1 t1-valueParameter descriptio
The VTP password settings and Huawei switch vlan configuration experiment results show you how to configure the vlan of a Huawei switch. Many people may not understand the vlan configuration of a Huawei switch, VTP transparent mode, VTP password settings, and V1, v2 integrat
fails, it will automatically remove the faulty port from the Trunk group, in this way, the traffic of each Trunk port is re-allocated to implement system fault tolerance. Iii. Precautions for TRUNK Configuration In a TRUNK, data is always from a specific source point to a destination point, and a single link is designed to process broadcast packets or uncertain packets. When configuring TRUNK, you must follow the following rules: 1: correctly select
Describes the overview and configuration methods of the Catalyst 1900 switch, the introduction of the Catalyst 1900 switch and the configuration of the Catalyst 1900 switch. The following describes the configuration of the
Configuration and management of brocade optical fiber switch (B/S) This article uses the Brocade 300 optical fiber switch as an example. The default IP address of the brocade switch is 10.77.77.77. the user name is admin and the password is password. 1. login Management Inte
You want to configure a switch alert. There are two methods:1. Console: You can directly configure the vswitch. 2. Remote Logon (Telnet): Use the TELNET program to remotely configure the vswitch with the configured IP address, generally, this operation can be performed only after the IP address of the vswitch is configured on the Console port.In addition to the above two methods, there are actually two methods:1. WEB
device) Stack slot-id priority (msater with lower priority) Stack timer mac-address switch-delay-time (mac switching time) Display stack Display stack peers (view status) After the stacked line is inserted (according to the intersection rule of one port and two ports of chrysanthemum), it is started and stacked. Configuration complete Then you will see the following situation: (how to configure a fool) Th
again. Diagnostic comments This fault is caused by a switch problem. During daytime work, the switch will be in a state of great time delay and change the transmission path of the switch to the Protocol. From the performance of the fault and the analysis of some STP/HSRP protocols monitored by OptiView, A vswitch with poor c
type.Step 2 set PVC with the fra1ne-relay route command.In this example, you need to use two terminal devices or routers and configure a frame relay switch. Before you startIt is helpful to make a PVC chart. DCE, PVC, and interfaces must be included in the chart. This example is shown in a chart that emphasizes the network from the perspective of hardware and se
interface that will be configured as a three-tier interface Step 3 No Switchport To get the physical interface into layer three mode Step 4 IP address ip_address subnet_mask Configure IP addresses and subnet masks Step 5 No shutdown Step 6 End Return Privileged Mode Step 7 show interfaces [Interface-id]show IP interface [Interface-id]Show Running-config interface [Interface-id] Confirm
In this article, we show you how to log on and enable privileges on a switch, which is critical for developers, and when Telnet controls the switch, these configurations become the knowledge that must be mastered! Switches are generally user name, password and privileged password (super password), these three kinds once combined together at least eight kinds of situation! As for which eight kinds, here is n
configuration statement of the standard ACL is:Switch # access-list access-list-number1 ~ 99) {permit | deny} {anyA | source [source-wildcard-mask]} {any | destination [destination-mask]}Example 1: Allow access from hosts on the 192.168.3.0 network:Switch # access-list 1 permit 192.168.3.0 0.0.255Example 2: Disable access from hosts on the 172.10.0.0 network:Switch # access-list 2 deny 172.10.0.0 0.0.255.2
example, a 24-port Mbit/s switch, the backboard bandwidth should be 24x2x100 MB = 4.8 GB. If the switching capability of a vswitch is greater than the bandwidth calculated using the above formula, the switch is usually configured with an expansion slot, and the excess switching capability is prepared for the expansion module.● FunctionsThere are many types of vs
. Authentication Sever can adopt standard Radius Authentication Server or service switch. The latter is mainly used in scenarios with a small network size (about 300 users, in the new software version, the Quidway 3000 and later vswitches of Huawei 3Com all provide the built-in Authentication Sever function, the user authentication configuration function is efficiently completed through the internal cluster
Common configuration commands for LAN switch MaintenanceFor the following information about LAN switch maintenance, please explain the Common commands in a blank space. LAN switches have evolved from a HUB-based LAN shared in the traditional sense to a broader space. The wide st5000 series local area developed by CiscoWww.2cto.comNetwork
Cisco LAN switches are still commonly used. So I studied the maintenance and configuration problems of Cisco LAN switches. I would like to share them with you here, hoping to help you. Cisco LAN switches have evolved from a HUB-based LAN shared in the traditional sense to a broader space. Take Cisco's ipvst5000 series Cisco LAN switch as an example. It includes a
Start building with 50+ products and up to 12 months usage for Elastic Compute Service
1 on 1 presale consultation
24/7 Technical Support 6 Free Tickets per Quarter Faster Response
Alibaba Cloud offers highly flexible support services tailored to meet your exact needs.
A comprehensive suite of global cloud computing services to power your business
Payment Methods We Support
