packet tracer

Tags: Linux plugin note ref CER class CISC get HTTPS77652571Https://linux.cn/article-5576-1.htmlTurn on login issues78587383Execute the following script in the root directory of the softwaresudo ./set_ptenv.sh sudo ./set_qtenv.shYou must follow the steps.installed in the default/opt/pt if the fallback is reinstalled on the default path because the home directory is installedSome dependent librariessudo apt install libqt5scripttools5sudo apt-get install libqt5multimedia5-pluginsLinux installed un

First, the experimental topology:Second, the experimental requirements:1, PC0 connection SW1, did not make any changes, see if F0/1 need to wait for 30s to become green;2, SW1 Global deployment of the default port Acceleration command, while the f0/2-5 deployed as Acess port;3, PC1~PC4 connection SW1, accelerate, the second into a green port, shorten the 30s, no longer wait.Third, command deployment:SW1 (config) #spanning-tree portfast Default! []SW1 (config) #int range f0/2-5SW1 (Config-if-rang

Tags: process proc ima RAC Technology share static term ADOBy configuring static routes, you can achieve an increase in routing entries for routers in a relatively simple network.However, if there are more than 20 routers in a network, it is difficult to configure static routes to accommodate the complexity of routing entries and changes in the network. At this point we can use the RIP protocol to configure simple dynamic routing, thus reducing the workload.Configuration ideas1 Configure the IP

policy in Router 2, specifying host and port7 The ACL takes effect under the port of the Router 2 Xia Lian serverNetwork topology1 Configuring Router 1 single-arm routing, establishing sub-interfaces and configuring IP addresses, etc.2 Configuring the Switch's VLAN and port type3 Configuring the IP address of the PC4 Configuring the interface address for Router 25 Configure static routes to communicate properly between networks6 Configure the ACL policy on Router 2 to allow PC1 to access the se

port to enable ACL policyNetwork topology1, configure Router 1, turn on the single-arm routing configuration subinterface address and connect the physical interface address of another route and open the port2 Configuring the VLAN of the switch, configuring the port type3 Configuring the IP address of the PC, specifying the gateway4 Configuring router static routing to enable network interoperability5 Create a new ACL policy on the destination router6 Enter the destination port to make the new A

Packet Tracer 5.0 Experiment (VII) router one-arm routing configurationFirst, the experimental target Master the single-arm routing configuration method; The communication between different VLANs is realized by single-arm routing. Second, the experimental backgroundAn enterprise has two main departments: Technical department and Sales department, divided into different offices, for securit

The newly released packet Tracer 6.2 version number is 6.2.0.0052, divided into student and teacher editions.Fixed some bugs on the previous version, added a new 819 router, a wired sniffer with trunking capabilities, and some new 3g/4g devices.The supported operating systems are WIN7,WIN8 or win8.1. Windows XP has stopped supporting it.Some features are supported for HTTP servers:(1) JavaScript and CSS Sup

000: 11: 23: % OSPF-5-ADJCHG: Process 1, NBR 192.168.3.1 on serial/0 from loading to full, loading dor2 (config-router) # endr2 # % SYS-5-CONFIG_ I: configured from console by consoler2 # Show IP routecodes: C-connected, s-static, I-IGRP, R-rip, M-mobile, B-BGP D-VPN, ex-VPN external, o-OSPF, IA-OSPF Inter Area N1-ospf nssa external type 1, n2-ospf nssa external type 2 E1-OSPF external type 1, E2-OSPF external type 2, e-EGP I-is, L1-is level-1, L2-is level-2, Ia-Is Inter Area *-candidate defaul

Packet Tracer 5.2 Experiment (15) network port address translation NAPT configurationFirst, the experimental target Understand the principle and function of NAT network address translation; Master NAPT configuration, realize LAN access to the Internet; Second, the experimental backgroundCorporate office network needs to access the Internet, the company only applied to the ISP a dedicated l

Packet Tracer 5.0 Experiment (ix) router RIP dynamic routing configurationFirst, the experimental target Master the configuration method of RIP protocol; Master to view the routes generated by RIP learning through dynamic routing protocols; Familiar with the connection mode of WAN cable; Second, the experimental backgroundSuppose that the campus network is connected to the campus netwo

ObjectiveLearning Network knowledge of the students have heard or used the network device Simulator, network equipment simulator known to have Huawei's ENSP, Third HCl and Cisco PACKET TRACER, Cisco's simulator with a simple operation interface, Easy to install and use and a variety of easy to work can win a lot of network engineers and students praise. Because I am short-sighted, I will be the most basic l

vty 0 4r1 (config-line) # password ABC123 // set the Telnet Remote logon password r1 (config-line) # loginr1 (config-line) # exitr1 (config) # interface fa0/0r1 (config-If) # IP address 192.168.1.1 255.255.255.0 // configure the management IP address of the router r1 (config-If) # No shutdown // enable port r1 (config-If) # End % SYS-5-CONFIG_ I: configured from console by consoler1 # Iv. PC logon Test Packet tr