psk innovations

Router tplink882 as a wireless switch: Connect the settings computer to any LAN port on the router, confirming that the computer has been set up to automatically obtain an IP address. The following figure: Note: To avoid IP conflicts or DHCP server conflicts, do not connect the router to the front-end network until the settings are complete. 1. Modify SSID (wireless name) Login to the Router management interface, enter the wireless settings >> basic settin

Router tplink882 as a wireless switch: Connect the settings computer to any LAN port on the router, confirming that the computer has been set up to automatically obtain an IP address. The following figure: Note: To avoid IP conflicts or DHCP server conflicts, do not connect the router to the front-end network until the settings are complete. 1. Modify SSID (wireless name) Login to the Router management interface, enter the wireless settings >> basic settin

, recommends that you use 1, 6, 11 frequency bands. Mode: Set your router's wireless operating mode, and recommend that you use the 11BGN mixed mode. Band Bandwidth: Set the wireless data transmission of the use of the channel width, available options: 20M, 40M and automatic. Maximum Send rate: Sets the maximum send rate for your router's wireless network. Turn off wireless security: Turn off wireless security, which means that your router's wireless network is not encrypted. WPA-

this process or through Task Manager to close this process. Confirm that no software process to upload to the outside, test the speed again, if close to your application bandwidth value, indicating that the speed is no problem, if the test out of the speed is significantly lower than the bandwidth you requested, please proceed to the next step. Verify that the wireless router is not being rubbed against the network. Open the wireless router's administrative interface (typically 192.168.1.1),

that you install 360 security Guardian Traffic firewall function to monitor the flow of each software process, found that such software process to the external high-speed upload, open 360 traffic firewall to limit the flow of this process or through Task Manager to close this process. Confirm that no software process to upload to the outside, test the speed again, if close to your application bandwidth value, indicating that the speed is no problem, if the test out of the speed is significantl

12345678 password we just set. Connecting now, Figure 12 The connection is on, see hint, figure 13 So we can get on the Internet. To be safe, we have to change the encryption method, preferably with WPA-PSK/WPA2-PSK AES encryption method, as shown in Figure 14 But this is not enough, now a lot of software can be cracked or found that we set the password, in order to

The SSID of the WiFi to be connected is "tHM", the password is 12345678, the authentication method is WPA2-PSK 1. Check whether the wireless network card driver is installed 1 xxx#iwconfig If you print wlan0 (or other name) of the wireless network card information, it indicates that the wireless network card driver has been installed, or to install the wireless network card driver can continue. 2. Configure/etc/sysconfig/network-scripts/ifcfg-wlan

method of setting AP mode for Tplink router 01 Login router, give power to the router that needs to be used as the switch (do not connect to the front-end network), operate the computer to connect to the LAN port, enter 192.168.1.1 in the browser and enter the management interface. 02 Modify the wireless signal, enter the wireless settings >> basic settings, set the wireless network name in the SSID number. 03 Enter wireless security settings, select Wpa-

in the "Internet account", "Internet password"--> "Next". 5, wireless network settings: Set the "SSID", the SSID is the name of the wireless network, attention can not use the Chinese--> select "Wpa-psk/wpa2-psk"--> set "PSK password"--> "Next". 6, click "Finish" At this point, the completion of the Tp-link tl-wr842n 300M w

Wpa_cli and wpa_supplicant interactions are through sockets,-p/var/run/wpa_supplicant is a socket channel. If it is directly into the command line operation interface as follows: WPA_CLI supported Operations Command everyone to run directly to the command view OK. The command to connect AP via WPA_CLI is as follows:1, connect the unencrypted AP Add_network1Set_network 1 SSID "Test_wifi"OkSet_network 1 Key_mgmt NONEOkEnable_network 1Ok The 1 returned when the Add_network is executed indicates th