qualcomm development board

A 51 Development Board was developed recently, as shown in. This board is very simple,All I/O ports are extracted, and Peripherals can be expanded by themselves. P0 is used to pull up the resistance,11.0592 M crystal oscillator, reset key, DC power plug, DC power self-locking switch, microcontroller lock seat, expansion of three VCC And Gnd. Compared with the lar

Setting up the test environment for the s3c6410 Development Board describes how to install Android on the Ok6410-a Development Board. Development boards are the main hardware devices for developing and learning embedded technologies. To be tested on the

The card computer boom triggered by Raspberry Pi has also led to the development of small-sized card computers by embedded developers in China. The well-known embedded developer in China, tianyinao technology and Feiling embedded system, also developed card computers. Now, we will compare the basic parameters of the embedded E8 chip computer with the OK335xS-II Development

Here are my IP settings: Local Connection IP Address: 192.168.1.23 subnet mask: 255.255.255.0 Default Gateway: 192.168.1.1 nbs The following are my ipsettings:Local Connection IP Address: 192.168.1.23Subnet Mask: 255.255.255.0Default Gateway: 192.168.1.1Preferred DNS: 202.96.128.86Development Board IP Address: 192.168.1.230Subnet Mask: 255.255.255.0Default Gateway: 192.168.1.1Preferred DNS: 202.96.128.86Virtual Machine Ubuntu IP: 192.168.1.108Subnet

This article goes from Schindler to Forum:http://www.topeetboard.com1. Install ADB driverTo debug Android apps on the Development Board , first install the ADB driver. Installed through theSDK Manager.exe. As shown in. It is also important to note that if you want to use theThe SDK Manager installs the software and needs to shut down Eclipse. After the installation is complete, open thecommand line cmd.e

When running programs on the developer board, you sometimes need to debug to migrate GDB to the Development Board. First download gdb:http://ftp.gnu.org/gnu/gdb/, I choose the latest gdb-7.11, download after the decompression, the next is configured and compiled ./configure--HOST=ARM-LINUX-GNUEABIHF--prefix=/home/xx If it's a 64-bit system,--HOST=AARCH64-LINUX

) \Init_timer_key ((timer), NULL, NULL)Register a Timer#define SETUP_TIMER (Timer, FN, data) \Setup_timer_key ((timer), NULL, NULL, (FN), (data))The following two functions are also available:Add a Timervoid Add_timer (struct timer_list *timer)Delete a timerint Del_timer (struct timer_list *timer)So what is the specific procedure for writing a timer?1. Initialize the kernel timer2, set the parameters of the timer execution function (optional)3. Set timing Time4. Set Timer function5. Start TimerN

By learning Android Deep Exploration (Vol. 1) HAL and Driver development in the fifth chapter to build the test environment of s3c6410 Development Board, I have mastered the method of building the test environment of s3c6410 Development Board1 Installing the Serial debugging tool: MinicomIn Ubuntu Linux, for example, y

1.S3C6410 Development Board Introduction:Different development boards differ mainly in the way of burning embedded systems, the Development Board integrates a variety of high-end interfaces, can help users achieve high-end product design. User-friendly two-time

I used to repost others' blogs all the time. Today, we can finally post original things and celebrate it. First, we attached the Development Board "Beautiful photos" created by three of our teachers and brothers. This board was referenced by the friendly arm micro2440. This board has condensed our painstaking efforts

Disclaimer: This article is an original work and copyright belongs to the author of this blog.All. If you need to repost, please indicate the sourceHttp://www.cnblogs.com/kingst/ Introduction This section describes how to compileProgramDownload to the Development Board. You need to download the program twice during the development of the program.

SD Card-----> Development Board1, Installation Preparation:Hardware connectionUSB Download cable, one end connected to the Development Board, the other end connected to the PC;Serial cable connection is good;The power cord is connected well;Set up the Development Board from

This article transferred from:http://www.topeetboard.comUbuntu System Burn-Write hardware platform : iTOP4412 Development BoardNeed to prepare: Serial line, card reader, an SD card is preferably 2G(Own), another card ( greater than or equal to 2G Yes, you can also use the U - disk )Software platformUbuntu operating system,Windows systemSuper TerminalImage files and compressed packages, in the Ubuntu folder of the CD , and the other 2 operating system

Android Communication with Development Board1, because we use this experiment is the serial port 2, that is, the serial port 2 to the WiFi core board use, change the jumper cap, so that the original serial port 2 is provided to ZigBee use, instead to wifi use.2. Add ser2net ApplicationLast time we succeeded in allowing the driver to support the serial port 2, and did a simple test. Next, we will add an appl

It's okay. I 've been playing with the company's development board. One day I wanted to integrate Google Maps, so I started to take action. The process is summarized into the following steps: 1. Create a project named GoogleMap Based on Google APIs The content of several important engineering documents is as follows: 1) Layout file main. xml There are two points to note: I. mapview: similar to other views

1, Guangzhou Chuang Long tms320c6748 DSP Development Board free trial, the history of the most abundant C6000 DSP Development Board, not to be missed.Application Link: http://bbs.ickey.cn/group-topic-id-57928.htmlApplication period: November 30, 2015Application Model: TL6748-EASYEVM, market price 1450 yuanNumber of app

The following are my ipsettings: Local Connection IP Address: 192.168.1.23 Subnet Mask: 255.255.255.0 Default Gateway: 192.168.1.1 Preferred DNS: 202.96.128.86 Development Board IP Address: 192.168.1.230 Subnet Mask: 255.255.255.0 Default Gateway: 192.168.1.1 Preferred DNS: 202.96.128.86 Virtual Machine Ubuntu IP: 192.168.1.108 Subnet Mask: 255.255.255.0 Default Gateway: 192.168.1.1

Boa is a very small Web server with only about 60 kb of code to be executed. As a single-task web server, BOA can only complete user requests in sequence, rather than fork new processes to process concurrent connection requests. However, BOA supports CGI and can execute a process for the CGI program fork. Boa is designed to speed and security. The following describes how to port A Boa Server. Environment HOST: fedaro 9 Objective: To develop the mini2440 Deve