ralink rt5370

Wi-Fi Alliance announces the completion of Wi-Fi direct standard, so that Wi-Fi devices do not need to connect to traditional home, office or hotspot network, you can achieve mutual connection, the relevant equipment certification work has begun, through the certification of products will get Wi-Fi certified Wi-Fi Direct identification. What is a Wi-fi point-to-point connection? According to Edgar Figueroa, executive director of Wi-Fi, the interconnection of Wi-Fi devices can be achieved anywher

The previous installments are doing the preparatory work, and this issue begins with the actual operation. Many of the beginning of the tutorial like to use HelloWorld to do a demonstration, I am no exception, in the Hardware Development Board tutorial running water is a HelloWorld, the program is simple, as long as the control gpio can be achieved, and intuitive obvious. Now start the HG255D implementation of the running water lamp function, the effect is as follows: If you're interested, let

--> OV9650 on the s3c2440 driver3.8 configure the NIC DriverMain Menu --> Netwoking support --> Networking options --> select Unix and TCP/IPMain Menu --> Device Drivers --> Network device support --> Ethernet (10 or 100 Mbit) -->Select 3.9 configure a USB wireless NIC DriverMain Menu --> Netwoking support --> wireless --> IEEE 802.11Main Menu --> Device Drivers --> Netwoking device support --> wireless LAN --> Wireless LAN (IEEE 802.11) --> Ralink d

: 1. Transplantation of arm + linux for wifi module rt3070 2. android wifi ralink rt3070 development record The situation on Tuesday is not optimistic. I almost want to give up because I have not compiled the WiFi driver module for Android. I subconsciously think that the driver module I compiled must be missing something. At least the driver module can be compiled now, and the kernel module can be inserted normally. However, I did n

Check the Ubuntu driver list, only Ubuntu10.04LTS support EW-7711UAn (https://help.ubuntu.com/community/HardwareSupportComponentsWirelessNetworkCardsEdimax), the original text is as follows: Workswith10.04LTS-RT3070USBdriverfrom Check the Ubuntu driver list, only Ubuntu 10.04 LTS support EW-7711UAn (https://help.ubuntu.com/community/HardwareSupportComponentsWirelessNetworkCardsEdimax), the original text is as follows: Works with 10.04 LTS-RT3070USB driver from

because many drivers are available for a variety of chip sets supported by mainstream open-source wireless software tools. You can select your preferred Linux version, compile or add data packets, or use Backtrack or KaliLinux in a simpler way. These versions are customized for Unbuntu or Debian, including the most popular and practical Security tools for penetration testing and digital forensics, by the Offensive Security sales company.For Wi-Fi adapters, if you are using Linux, you can save y

G4 series has a lot of models of machines, depending on the model of the machine configuration is not the same, so the machine will not be the same as the drive, so we can not separate from the serial number for you to provide the wireless card driver for your machine, if you need to find your machine wireless card driver, It is recommended that you check the following official documents to find out:http://h20566.www2.hp.com/portal/site/hpsc/public/kb/docDisplay/?docId=emr_na-c02903029Note: Thi

command enters the buildroot compile configuration interface under the terminal:make menuconfig;The CPU chip of the device we used in the tutorial is the MT7620 series (mt7620a/n), the following begins the most basic configuration for the MT7620 series of devices, the steps are as follows: 1.Target System (Atheros AR7xxx/AR9xxx) --->Enter the next turn after the space selectionRalink RT288x/RT3xxxThen return to the back, and the compile target is:Target System (

manufacturer ).). Because the duplicate vid and PID does not seriously affect the use of the product, many USB equipment manufacturers (most of the factory in shanzhai) do not apply for their own vid from the USB forum for convenience. Is still using the vid of the master manufacturer or writing vid and PID to the product. At the same time,Regular manufacturers only need to apply for vid,The PID is determined by the manufacturer.So there are products of the same model, and different Controll

First confirm the interface of the SD card (it is said that there are 2 kinds of the first is the Sdio the second is SPI if neither of them, then can be made like a card reader device, that is, USB devices)I have this one on the SPI interface, then the SPI module on the kernelKernelmodules ---> SPISupport ---> *kmod-mmc-spiSave exit, the first make burn is discovered or not recognized. The reason is that the SPI is turned off by default in the source code of OpenWrt.Modify the releva

switched to Apt-get to update the system and software online. If you install the Deb package separately, you can only use the dpkg command,There is no GUI gdebi integrated with dpkg. Of course, these solutions can be found from many Ubuntu tutorials.The biggest benefit of bt4 pre final core architecture change is that a large amount of ubuntu resources and methods can be used. The driver of the wireless network card is described as follows:1. The latest firmware file of UBS is not integrated, s

wireless route. because most of them are encrypted by WPA and wpa2, The wpa_supplicant tool is used. Create a wireless network card running directory on the Development Board terminal: Mkdir-P/var/run/wpa_supplicant Create the/etc/wpa_supplicant file. The file content is as follows. The SSID is the network name and the PSK is the password. Ctrl_interface =/var/run/wpa_supplicant Network = { SSID = "AAA 001" Scan_ssid = 1 Key_mgmt = WPA-EAP WPA-PSK ieee8021x none Pairwise = TKIP CCMP Group = cc

I recently contacted openwrt to develop customized firmware for MT7620A. I want to compile the source code on https://github.com/qdk0901/openwrt-mt7620. thank you! One major problem encountered was the USB mounting problem. After a long time, I checked the usb Module in wiki several times and finally solved the problem by modifying the source code. The method is as follows: Modify: target/linux/ramips/dts/mt7620a. dtsi file Ohci @ 101c1000 {compatible = "r