realtek 8812au

: Intel Corporation Wildcat Point-LP MEI Controller #1 (rev 03) 8 00:1b.0 Audio device: Intel Corporation Wildcat Point-LP High Definition Audio Controller (rev 03) 9 00:1c.0 PCI bridge: Intel Corporation Wildcat Point-LP PCI Express Root Port #1 (rev e3)10 00:1c.1 PCI bridge: Intel Corporation Wildcat Point-LP PCI Express Root Port #2 (rev e3)11 00:1c.2 PCI bridge: Intel Corporation Wildcat Point-LP PCI Express Root Port #3 (rev e3)12 00:1c.3 PCI bridge: Intel Corporation Wildcat Point-LP PCI E

-restart the computer after the update is complete. If both of these cases are not present, please see the following steps directly. 　　Step ③: If there is no small horn in the lower right corner of the desktop, start-control panel-sound and Audio devices-check "put the volume icon into the taskbar"-OK. 　　Step ④: Click on the lower right corner of the desktop small horn--options--attributes--All options tick tick click "OK", you will see a long window, and a lot of it has not been shown, pullin

1: I don't want to go offline in my desktop. So I went to a certain East to buy a USB wireless network card. The WN725NUSB of tp is very small, which is about the same size as that of the Logitech USB adapter. 2: The driver can identify it by itself. since it is a usb Nic, after the USB is inserted, lsusb will see a new line of Realtek id0133: 8179root @ debian:/# lsusbBus00 added. 1: I don't want to go offline in my desktop. So I went to a certain Ea

connections in the host's network connection, the VMware network Adapter VMnet1 and the VMware Network Adapter VMnet8. The system installed in the virtual machine is connected by these two virtual network cards. such asSimilar antiarp firewall on the host must be turned off or the virtual machine will not be able to surfThere are several options: 1, bridged (bridge) mode: If the host is Internet access through the LAN, the virtual machine can be used with the host network segment, gateway and D

difficult for some cases (IP and Mac binding, network management does not agree. In addition, the VM cannot communicate with the host through the network after the network cable is unplugged from the host. This problem does not occur in the next few cases. Therefore, the bridge mode is not used. 1) Host IP information 2) set the VMware network connection to bridged. 3) Virtual Machine System Network Settings Multi-nic bridgingWhen I have dual NICs, although vmnet0: bridged to a

some cases (IP and MAC binding, network management does not agree. In addition, the VM cannot communicate with the host through the network after the network cable is unplugged from the host. This problem does not occur in the next few cases. Therefore, the bridge mode is not used.1) Host IP information 2) set the VMware network connection to Bridged. 3) Virtual Machine System Network Settings Multi-nic bridgingWhen I have dual NICs, although VMnet0: Bridged to an automatically chosen adapter

machine can only bridge the "local connection" (via Nic), not the "local connection 2" (RealTek Nic) InVirtual Network Editor-> In the briic bridging Tab If we want to bridge the "local connection 2" (RealTek Nic), we need to add "via nic" in "exclude adapters" (local connection ), in this way, "Local Connection 2" can be bridging. However, "Local Connection" (via Nic) is not acceptable, even if you rem

Connection 2" (Realtek network card)In the virtual Network Editor, Automatic bridging tabIf we want to bridge the "local Connection 2" (Realtek network card) need to "Exclude adapters" add "via Network card" (local connection), so that "local connection 2" can be bridged. However, "local connection" (via network card) is not possible, even in "Exclude adapters" remove "via network card" is not, I guess VMw

Please note: before adjusting, please make sure your computer has a built-in microphone, the sound card driver is properly installed, and please temporarily turn off QQ or other software that needs to call the microphone before adjusting. The sound card driver name is Realtek high Defenation Audio Can be seen in the Start-Control Panel-programs (Programs and functions)-Uninstall Programs list This article takes

"shortcut" four words Integrated Drive: =========================== It is a waste of time for the technician who is engaged in this task to spend the day in the drive. With integrated drive technology, the installed staff can be freed from this repetitive work. System home Fast installed CD can be more perfect for a variety of hardware installation drive. Automatic installation of the driver will not delay the time to install the system, and the effect is the same as the manual installation. W

= {{0x10ec, 0x8129, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 1 },{PCI_ANY_ID, 0x8139, 0x10ec, 0x8139, 0 },{0 ,}}; The driver is used to drive the device, so the probe function in rtl8139_pci_driver is called rtl8139_init_one, which is defined in our driver, it is used to initialize the entire device and make some preparations. Note that pci_device_id is a structure defined by the kernel to identify different PCI devices. For example, 0x10ec here represents Realtek