is the primary. however, for physical NICs, except for the first configured IP address, the added IP address can be regarded as secondary. the ip ifconfig command added here is invisible.As far as I know, adding a secondary ip
address. Updates its ARP cache with the source host's IP address and hardware address. The source host receives the reply and establishes the communication. resolves remote IP addresses hosts on different networks communicate with each other, and the ARP protocol broadc
1, Introduction to basic knowledge
1. 1 each host or router in the network has at least one IP address;
Two devices are not allowed to have the same IP address on the Internet;
1. 2IP address using a layered structure;
The
hosts section, where the physical network is used to identify the different physical networks under the same IP network address, which is the subnet.Class A IP segment 0.0.0.0 to 127.255.255.255Class B IP segment 128.0.0.0 to 191.255.255.255Class C IP segment 192.0.0.0 to 2
, just suggestions, ideas (think of sleep), because they are not intranet, so there is no way to test, we need to study, according to the following methods, I think it should be possible. ) is as follows: (for intranet, the first is not the use of peanut shells such software)The first step: to find the "port mapper" This software, your local area network, to do as Mu run the server's IP "map" to connect the Intenet network of devices on the
255.255.255.255: Broadcast address. IP address 0.0.0.0: Represents any network. The host bit is all 1: Represents the broadcast address of the network segment, that is, all the hosts of the network segment. The host bit is all 0: represents the network address of the networ
Create A point-to-point VPN for A fixed IP address of the network component. Create A point-to-point VPN for A fixed IP address of the network component router. one end of the network component router A is connected to the LAN. Th
it on the network. There are several groups of IP addresses that are specially reserved for use by the local network. The Internet backbone router cannot be identified. For example, the IP address of the author's computer is 192.168.1.127. If you enter this address in your
A router is a basic device in man, Wan, and Internet. It connects to a remote computer network distributed in a certain region and forwards data packets based on the layer-3 IP address of the OSI reference model. The simplicity, openness, and scalability of IP technology make it widely used in the Internet and broadban
The ipad and iphone have a consistent approach to configuring IP addresses, and this article only takes the ipad as an example.
STEP1 : Open IPAD main interface, select " Set up " menu, select the Wi-Fi ", enter Wi-Fi set the page as shown in the following illustration.
STEP2 : Open the wireless switch, search the wireless signal, as shown in the following figure.
STEP3 : Select any one of the wireless networks on the right. ">" button (in t
is used for direct connection to the host, and can be used by global. Not only does the IP address have the scope attribute, but also routes have the scope attribute.2. Which network port does the ARP request enter? ARP replies must be sent from the network adapter. For more information, see the arp_process function. Because the entry Dev is also part of the route look
Firewalls can be divided into several different security levels. In Linux, because there are many different firewall software options, the security can be low and high, and the most complex software can provide almost no penetration protection capabilities. However, the Linux core itself has a simple mechanism called "Disguise". Apart from the most specialized hacker attacks, it can withstand the vast majority of attacks.
When we dial up the Internet, our computer will be assigned an
IPv4 address category:
I. Composition1. Use a 32-bit address. 2. It is expressed in dotted decimal notation. For example, 172.16.0.0. Each number corresponds to eight binary BITs, which are called a single-bit group (octets ). For example, if the IP address of a host is 128.10.2.1 in binary format, the
CatalogueErrors and solutions in a network configurationIntroduction to the three modes of network configuration under two VMware 1. Bridging mode (bridged) 2. Network address conversion Mode (NAT) 3. Host-only mode (host-only)Errors and solutions in a network configurationError 1: Everything is fine after the virtual machine is installed, and after a day of use it is discovered that the IP
the host receives an ARP request or sends an answer, it puts the hardware address and IP of the requesting side into the ARP cache. This way, when the TCP connection is established, the answering side does not need to send ARP to resolve the IP.If you attempt to connect to a non-existent host, multiple ARP requests are made and an incomplete entry is saved in the ARP cache. There is a time-out retransmissi
We have said that the Internet is a large inter-network that connects countless networks around the world. Computers in each network are uniquely identified by their own IP addresses. Therefore, we can imagine that, on the INTERNET, each network also has its own identifier.This is very similar to the phone number in our daily life. For example, if a phone number is 0515163, the first four digits in the number indicate the region of the phone number, t
thing. There is also a kind of tool through the TeamViewer remote capture to the desktop, the advantage is because it is the local session so there will be no graphics card problems, but there are many shortcomings, one is not efficient enough, often card, there is a in case the account dropped the basic game over.So in general I am a combination of two, the need for efficiency when using remote Desktop, the need for a video card when the TeamViewer. But the principle of remote Desktop does not
.
The local IP address is configured as follows:
The local IP address is 10.10.1.4.
In addition, if the same LAN is not connected to a router (including a layer-3 Switch), it uses a layer-2 switch or a fool switch orHubConnectedPC, As long as there are two or more mac
host. After receiving the answer, the source host establishes communication.
Resolve remote IP addresses
Hosts in different networks communicate with each other. ARP broadcasts the default gateway of the source host.
If the target IP address is a remote network host, ARP broadcasts the IP
necessary information to transmit the encapsulated data in the IP packet. The data structure and description of the IP header are as follows: the member length (BIT) describes the version number of the IP header of version 4, is currently IPv4, the latest is IPV6 header length 4 IP header, if there is no special choi
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.