segger jtag

Because the Development Board on hand is relatively old, it is botron's netarm2410 and can only be started from nandflash. The hardware at hand is incomplete. There is only one simple Wigler JTAG. Here we recommend H-JTAG software, the latest version added support for nandflash, very easy to use. 1, first select the NAND-FLASH under the + jk9f1208 2. Click Check in the programming column to see

When debugging the H-JTAG, there will be a solution for "can't halt the target and make it enter debug state; First: power-off, short ISP, on the lpc2400 Development Board is the jp6 in the lower left corner, and then power-on, programming several times on the number. Second: Check the datasheet of norflash, find the address pin of norflash, connect to norflash, and repeat it several times. Cause: Improper debugging of the H-

JTAG Pin:First, SWD and the traditional debugging mode difference1. SWD mode is more reliable than JTAG in high-speed mode2. When the GPIO is just missing, you can use the SWD emulation, which supports fewer pins3. The SWD mode is recommended when the size of the board is limitedSecond, the emulator to the SWD mode support situation1. The common emulator on the market for the SWD mode support situationJLINK

JTAG (Joint Test Action Group) is an international standard Test protocol used for internal chip testing and System Simulation and testing. JTAG is an embedded debugging technology. It encapsulates a special Test circuit (TAP) in the chip ), use a dedicated JTAG test tool to test internal nodes. The standard JTAG in

Overview: QpstIntegrated tools, transfer files, view the device's EFS file system, and download code QidcTest RF QxdmView log JTAG trace32Debugging Qpst and qxdm usage instructions. For details, refer to the resource files I uploaded to csdn. I read them all and read the user guide, which is simple. Qpst is a transmission software developed for Qualcomm chips. Simply put, mobile phones that use Qualcomm's processing chips can theoretically use qpst to

Hisi hi3515 is composed of the kernel of arm9-+ DSP. You can use h264 to encode 4 d1 or 1 1080 p or h264 to decode 4 d1 or 1 1080 p. At the same time, the chip itself has a variety of peripheral interfaces uartx4 satax2 USB hostx2 sd spi lan ir I2C VGA output CVBS output and a large number of gpio, etc. On the software, the system runs Linux 2.6.24 and uses the GCC/g ++ compiler. Core board composition Hi3515 + DDR (2 Gbit) + flash (256 Mbit/32 Mbyte) + rtl8201 + resetIn pursuit of stabilit

In fact, the memory in the vro consists of three parts: the header is CFE, which is actually the BIOS we are talking about. The following is the NVRAM and firmware area (the two did not study before and after ). Many of my friends want to use the JTAG line to refresh CFE (for example, if you want to modify some default configurations, or activate memory or overclock). The speed of 8-bit transmission of this parallel port is really slow, In fact, if th

data register connected between TDI and TDO shifts data one stage towards the serial output with each clock.Exit1-drTemporary controller state.PAUSE-DRThe shifting of the test data register between TDI and TDO is temporarily halted.Exit2-drTemporary controller state.Allows to either go-to-shift-dr state or go-to-update-dr.Update-drData contained in the currently selected data register is loaded to a latched parallel output (for registers that has s Uch a latch).The parallel latch prevents chang

>_It was okay last night. I couldn't debug it this morning. When I downloaded the program, I always reported that J-link could not be connected, and the stm32 seemed to have crashed. The LED lights did not flash, and the tftscreen was not displayed. >_ I thought it was a problem with the J-Link driver, but after I re-installed the driver and restarted the computer, it still didn't work ~ At last, someone on the Internet said that boot0 was connected to a high level, so I found the boot0 foot of

Here's how:(1) Burn the efuse as follows Enable_sw_jtag_con bit.[Security Control]; If Enable_sw_jtag_con = 1, Enable SW control to JTAGEnable_sw_jtag_con = 1(2) in the alps\mediatek\custom\$ (project) \securit\chip_config\s\cfg\secre_jtag_config.ini fileSecure_jtag_enable set to FALSE, rebuild build imageNotes:(1) The above method is not a permanent disable JTAG, if you want to re-restore the JTAG function

This page presents some advice regarding adding a JTAG connector to your avr-based system during design. The Atmel JTAG ICE User ' s Guide was the definitive source of information on this subject and nothing here should be taken T o contradict or supercede it. The JTAG HeaderThe picture in right shows the layout of a JTAG