sf pim

group brief Run the show ip igmp command to determine the queried server. Start IP Multicast Route Selection: Router (config) # ip muticast-routing PIM on the startup interface: Dalllasr1> (config-if) # ip pim {dense-mode | sparse-dense-mode} Start the PIM in dense mode: Router # ip multicast-routingRouter # interface type numberRouter # ip

. Previous Page [1] [2] [3] [4] Next page Article entry: csh responsible editor: csh 63. Start IP Multicast Route Selection:Router (config) # ip muticast-routing 64. PIM on the startup interface:Dalllasr1> (config-if) # ip pim {dense-mode | sparse-dense-mode} 65. Start the PIM in dense mode:Router # ip multicast-routingRouter # interface type numberRouter # ip

Here is a foreigner's blog, which raises a question about whether andromda is actually an MDA: Http://andrej.racchvs.com/archives/2003/08/10/is-andromda-really-a-mda-tool/ The content is as follows: Is andromda really a MDA tool?The andromda project just released version 2 of their tool. according to their website andromda is an open source code generation framework that follow the model driver architecture (MDA) paradigm. it's a nice tool which will generate J2EE code based on XML diagrams save

content in the ARP cache.57. to configure the vro as a member of the HSRP backup group, run the following command in Interface Configuration Mode:Router (config-if) # standby group-number ip address-address58. In the interface configuration mode, to allow a vro to resume its forwarding role:Router (config-if) # standy group-number preempt59. The access time and retention time parameters are configurable:Router (config-if) # standy group-number timers hellotime holdtime60. Configure HSRP trackin

Myread2=myfso.opentextfile (Server.MapPath ("./new_list.asp"), 1,0)If Myread2.atendofstream ThenResponse.Write "No news content"Myread2.closeResponse.EndEnd IfMytext2=myread2.readallMyread2.closeDim listarray,i,h,count,sf,titleListarray=split (mytext2, "|") ' ######## #读取记录并以 # split into Listarray arraysCount=ubound (Listarray)For i=0 to count ' ########## #根据ID找到该新闻实现删除功能Sf=split (Listarray (i), ",")If R

MDA has been put forward for 5 to 6 years. Its main standards are MOF, UML (including OCl), XMI, and CWM. Currently, qvt (query, view, and conversion of models) is a standard being developed ). These standard families are associated with each other to form the huge architecture of MDA. It can be said that MDA is composed of a series of standard families and the idea of model-driven development. The subsequent researchers have different focuses based on their own interests, resulting in the split

1, the problem description: We have a CPE MP1803 router as a customer's CE router, the PC after the IGMP report, our router will be in the IGMP table to write the multicast group, but the customer said that the upstream of the PE device does not receive the PIM of our equipment Join message and ultimately cannot draw the multicast traffic down. After the investigation, found that customers in the same local area network has multiple CPE, and our MP1

, interoperability, and reusability through the separation of modularity. InMDAThe software development process is driven by the Modeling Behavior of the software system. Below isMDASoftware development cycle: MDA There is no big difference between the life cycle and the traditional life cycle. The main difference is that the artifacts created during the development process, including Pim ( Platform Independent Model , Platform-independent

addresses are: 224.0.0.1-All multicast hosts in the CIDR block.224.0.0.2-All vrouters supporting multicast in the CIDR Block224.0.0.4-All DVMRP routers in the CIDR Block224.0.0.5-All OSPF Routers224.0.0.6-All OSPF assigned Routers224.0.0.9-All r00002 Routers224.0.0.13-1/256 of the IPV6 address space of all PIM routers is allocated to multicast addresses. An FF11111111 value indicates that the address is a multicast address. The identifier segment is

In previous articles, we have explained the content of the IPv6 protocol. We should remember that in IPv6, there are unicast IPv6 routing protocols and IPv6 multicast routing protocols. Now let's take a look at the latter. What content does the IPv6 Multicast Routing Protocol contain? Let's take a look at the following content. IPv6 Multicast Routing Protocol IPv6 provides rich multicast protocol support, including MLDv1, MLDv1 Snooping, PIM-SM,

The current mobile phone has been used for four and a half years. It has been broken for n times, but it has never been broken. Recently I want to change to a Windows Mobile Phone. Before changing the phone number, let's make a try on this old mobile phone. The old mobile phone only supports j2_m2. Use it to back up the address book. Follow these steps to back up your phone address book: 1. Save the address book content to a string through the PIM-rel

shared tree is to save resources, but the path from source to destination is not necessarily the best Five, PIM PIM is IP routing protocol-independent, independent of the routing protocol, but still need to have a routing table exists, This is a requirement to prevent loops. PIM is divided into sparse mode and dense mode six, IGMP and cGMP IGMP v1: Include

The premise for multicast to communicate normally is to set up a multicast tree, multicast tree to normal establishment, RP must know the multicast source and group members, if the same PIM-SM domain, the RP want to know all the multicast source and group members is very easy, but the RP has no way to know the other PIM-SM domain multicast source. To solve this problem let a

13. multicast routing protocol-PIM (protocol-Independent Multicast Routing Protocol) Multicast Routing Protocol classification-dense mode and Sparse Mode Multicast branch tree 1. STP ---- source tree, Shortest Path Tree To maintain table items (S, G), it indicates the tree closest to S) It consumes a lot of memory because it needs to maintain one S and G for each source. Fast data forwarding and low latency 2. Shared tree ---- RP tree, core tre

software environment, the performance of the vswitch will be seriously reduced. The CGMP method is to use a vro to tell the vswitch the group MAC address and host MAC address of the multicast members so that the vswitch can know that there are Members on that port and forward the packets.4. How to Use multicast routing protocols commonly used in www.2cto.com? Because mainstream router products only support Pim, other router protocols do not, therefor

the information required at the final stage of forwarding Multiple Multicast packets to the destination. Multicast routers exchange information with each other, which is collected from members of the group of hosts directly connected to them. The algorithms used to exchange route information between multicast routers include flood, spanning tree, reverse route broadcast, and reverse route multicast, some algorithms are used in dynamic multicast routing protocols, such as distance vector Multica

Environment: eclipse3.3.0 + myeclipse5.5.1ga (spring2.0 + struts1.1 + hibernate3.1) The error is: Java. Lang. nosuchmethoderrorCode:15:20:54, 093 error contextloader: 203-context initialization failedOrg. springframework. beans. factory. beancreationexception: Error creating bean with name 'sessionfactory 'defined in class path resource [applicationcontext. XML]: Invocation of init method failed; Nested exception is Java. lang. nosuchmethoderror: Org. objectweb. ASM. classvisitor. visit (iiljava