the method of Tp-link router Lan-wan cascade setting
Before setting, please reset the router (Restore factory settings).
Reset method: Under the power state, long by the router reset key more than 5 seconds to loosen, reset successfully.
The first step, the computer to co
This article talks about QOS settings and connections in dual-wan router settings. The problem remains to be solved. The issue should be released for your reference and further solution. You have to rely on experts for help!
How to configure TP-LINK routing for a dual-wan router
Now I am using two 2 m ADSL databases
tp-link wr800n Wireless Router Setup method
The Tp-link wr800n wireless router is connected to the power supply and the notebook is wirelessly connected to the wireless signal of the
Tp-link Router tplogin.cn not open the solution
1. Check Line connection
Check that the computer's network cable is connected to the correct port (1, 2, 3, 4 arbitrary LAN port) to ensure that the computer cable interface and router corresponding to the interface of the indicator (green) normal.
Cable Co
The TP-Link wireless router is still widely used. So I studied the settings of the TP-Link wireless router. These methods are not very familiar to general users, here is a detailed introduction. Now, more and more users share Inte
When do I use WDS bridging?
It is generally used in a large area, a wireless router with limited signal coverage, making certain areas of the site without signal or weak signal; This can add a wireless router and configure the WDS bridge to allow wireless WiFi coverage throughout the site.
To set the method for Tp-link
Tp-link tl-wr882n Router WDS bridge setup case
For example, users need to prepare 2 tl-wr882n routers, for the convenience of identification, we mark the main router A and Vice Router B, where the primary
With the development of China's routing industry, the market demand for wireless routers is also gradually increasing. Here we mainly introduce the TP-link TL-WR340G wireless router and evaluate it. In the home wireless router market, the Chinese brand TP-
small computer icon in the lower right corner of the computer after success . , the Support tab in the local connection state can see the parameters that the computer gets, as shown in XP system as an example):
setup is complete, try to log on to the router management interface 192.168.1.1 . If you cannot open it, continue to the next action.
4 , and restore the
TP-LINK router is our commonly used network equipment, this paper for TP-LINK routing port ing problem, gives a detailed description of the operation, and gives a detailed description, I believe that after reading this article will be helpful to you.
First, find the
Release date: 2013-03-21Updated on: 2013-03-22
Affected Systems:TP-LINK TL-WR740N v4.23Description:--------------------------------------------------------------------------------Bugtraq id: 58623The TL-WR740N is a Mbps wireless router.TL-WR740N 3.16.4 Build 130205 Rel.63875n vro has a remote denial of service vulnerability in implementation. If the Web server (httpd) does not process http get requests on the default TCP port 80, the attacker sends a
Vro achieves Internet sharing
Currently, the use of home broadband is divided into several homes by a single broadband, and the speed is enough. In order to save some money, we can share the Internet. Several people use the same ADSL line, this requires a router, the following I will take the TL-R402 router, for example, with the illustrationTP-LINK
Tp-link tl-wr742n Router set up wireless WiFi diagram Step one, set the TL-WR742N router wireless network name
Login to the TL-WR742N router's settings interface, click "Wireless Settings"--> "Basic Settings"--> set "SSID number".
Note the problem:
(1), "SSID" is the name of the wireless network (WiFi),
TP Link Wireless Router traffic settings, can be effectively guaranteed in the same LAN under each device can be balanced Internet access. Eliminates the video and so on a series of occupy the speed of the process and not open the Web page, with a special network card phenomenon. So how does the TP
Tp-link Router failure
If the following figure shows up after the router is set up, the IP address, subnet mask, gateway, and DNS server are not visible, and there may be several reasons for dialing problems.
Cause and solution of Tp-
Hardware Connection , first of all, the cat (modem) above the network cable connected to the WAN port on the Tp-link, and then use a network cable to connect the computer and Tp-link, general Tp-link above have several mouths, res
Suddenly off the net, the previous landlord's router management page can be opened, today suddenly will not open. Ping the next, you can ping the same, so I think of the landlord's router is tp-link can telnet login.Every time I break the net, I will restart the landlord's router
Procedures for Tp-link wireless router upgrades
Tp-link wireless routers in the upgrade, there are two main ways to upgrade the TFTP upgrade mode and the way the Web upgrade.
One, TFTP upgrade way, this way needs to first open TFTP service, and then landed
Wireless RouterAlthough it is widely used and easy to use, there are still many friends who are new to wireless routers and do not know how to set up wireless routers. After all, it is not the same as non-Network-managed switches, plug in and use it. Vendors generally provide instructions, but some of them are not concise and complex. Although some provide installation guides, they are obviously unable to reflect the customization of wireless router s
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.