usb flash drive floppy emulator

caseUS_ SC _SCSI: 699 us-> protocol_name = "Transparent SCSI "; 700 us-> proto_handler = usb_stor_transparent_scsi_command; 701 break; 702 703 caseUS_ SC _UFI: 704 us-> protocol_name = "Uniform Floppy Interface (UFI )"; 705 us-> proto_handler = usb_stor_ufi_command; 706 break; 707 708 # ifdef CONFIG_USB_STORAGE_ISD200 709 case US_ SC _ISD200: 710 us-> protocol_name = "ISD200 ATA/ATAPI "; 711 us-> proto_handler = isd200_ata_command; 712

USB flash drive to install Linux system, unplug the USB drive system cannot bootProblem Description:Use a USB stick to install the Linux operating system, excluding the USB stick, unabl

pm_mutex;/* protectspm operations */ 400 401 unsignedlong last_busy;/* time of last use */ 402 intautosuspend_delay;/* injiffies */ 403 404 unsignedauto_pm: 1;/* autosuspend/resume in progress */ 405 unsigneddo_remote_wakeup: 1;/* remote wakeup shocould be enabled */ 406 unsignedautosuspend_disabled: 1;/* autosuspend and autoresume */ 407 unsignedautoresume_disabled: 1;/* disabled by the user */ 408 # endif 409 }; 410 # define to_usb_device (d) container_of (D, struct usb_device, Dev) It looks

Because the USB driver in Linux is already very complete,You only need to follow the following configuration. After the configuration, recompile the kernel and install it on the Development Board. 1. Modify make menuconfig System type --> Input core support --> SCSI device support ---> [*] Legacy/proc/SCSI/support * ** SCSI support type (disk, tape, CD-ROM )*** [*] Hid devices ---> --- Hid Dev

Two methods:One: During installation:After the custom creation of the partition,Select the location where the system launcher is installed, in the change deviceSet the first start device, and the second start device!Second: After installation: Boot does not enter the system press F2, enter the BIOS After entering the BIOS, change secure Boot to Disabled Finally, change boot List Option to Legacy Reboot, OK! How to start the USB

, here, the usb_class_mass_storage macro is defined in include/Linux/USB/ch9.h, and its value is 8. Let's take 1,477th rows as an example. 1477 usual_dev (us_ SC _rb, us_pr_cb, usb_us_type_stor ), Expand this macro, that is, define such a usb_device_id struct variable, its match_flags = struct, and binterfaceclass = usb_class_mass_storage, binterfacesubclass = us_ SC _rb, and binterfaceprotocol = us_pr_cb. Usb_class_mass_storage does not need to be

1. Right-click "computer"-"device manager" on the desktop on the computer, and click "menu bar-> view-> sort devices by connection" on the displayed page:2. As shown in the figure above, the device should be a usb storage device, and then go to the directory:, find a folder starting with usb Stor, copy and download the folder, and paste it on the desktop, as shown in the figure

No optical drive to teach you how to create a USB flash drive to start the systemPeople's shoulders, that is, the load balancing effect ". People with notebook knowledge know that cost-effectiveness and portability are positive and negative propositions in The Notebook field. They are always opposite and cannot get alo

How to install winpe + ghost + virtual optical drive with a USB flash drive How to install a system with a USB flash drive● Preparations before installing the systemA

/sda1 may be treated differently based on the actual situation. I made it into hda1, and the result could not be loaded with extra because it could not be found. Later I found that Linux recognized it as sda1. Chinese: kernel/cdlinux/bzimage root =/dev/ram0 cdl_lang = zh_cn.utf8 cdl_dev =/dev/sda1 then read mclinux again. I downloaded mclinux1.0 and mclinux2.02, mclinux1.0 is an IMA floppy disk image file, so it can be directly guided by a

The following describes how to install Fedora8 or Fedora9 to a USB flash drive in Windows. The ora installed in this way can be used like a system on a hard disk, and after the next restart, all your settings are still saved. Article 2. decompress the downloaded file The following describes how to install Fedora 8 or Fedora 9 on a