vdsl2 router

One 1.router (config) #router rip start RIP process 2.router (conifg-router) #network 172.17.0.0 The primary network that specifies the RIP protocol 3.router (config-router) #passive-interface F0/1 to configure F0/1 as passive

tplink886n Router Setup method Tp-link tl-wr886n Wireless Router Step one, tl-wr886n router installation 1, telephone line Internet: Please prepare 2 short network cable, a network cable used to connect ADSL Modem (cat) and tenda/' target= ' _blank ' > Tengda tl-wr886n A WAN interface for a router, and

A few months ago bought a Tplink wireless router, according to the instructions set up after the normal use of a period of time, useless, and then found that can not use! In accordance with the instructions set IP and DNS all automatically obtained, or not go into 192.168.1.1, the IP set to 192.168.1.X (1-255), Gateway set 192.168.1.1, also or not go to 192.168.1.1, also tried to send the router back to the

The network bridge can connect two different physical local area networks, it is a kind of storage and forwarding device that realizes LAN interconnection in the link layer. The Network Bridge receives the MAC frame from a local area network, after unpacking, proofreading, verifies, presses another LAN's format to reassemble, sends to its physical layer. With the development of wireless network, more and more companies and enterprises have already started to layout wireless LAN, today we mainly

With the growing sophistication of wireless technology and the continuous enrichment of wireless products, the need for people to use wireless networks is increasing. Because of its simple network and convenient use, the wireless router has become the main mode of the network, so it has been paid more and more attention to the methods and techniques of the fault handling of wireless networks. This article will introduce the common but very easy to ign

Router tplink845 Wireless bridge unsuccessful solution: For older products, in the Admin interface click Run Status > Wireless status, WDS status continues to display scanning, initialization, correlation, etc., as shown below: The above phenomenon indicates that the WDS bridge did not succeed. Use the following methods to troubleshoot problems. 1, confirm the bridge is the correct signal When you set up a wireless bridge,

tplink885n setup steps as follows A new purchase (Restore factory settings) of the tl-wr885n router, to achieve the Internet function, need to carry out the following 3 steps: 1, tl-wr885n router installation, 2, set the computer IP address, 3, tl-wr885n router Internet settings. Step one, tl-wr885n router installati

Broadband routers are the necessary devices for sharing the Internet, and multiple computers are connected to receive distributed signals from the broadband router. Therefore, this aspect of maintenance and troubleshooting work can not be ignored. Therefore, this paper selects the most common fault phenomenon in the daily use of the broadband router, and puts forward the solution. Hope that through this art

tl-wr842n Router WDS mode Setup diagram Step one: View the wireless parameters of primary Router a Please enter the interface of the master router A to view and record the following: Wireless signal name, wireless encryption mode, wireless password, wireless channel (channel please manually set one), as shown in the following figure. Puling tl-wr842

When do I use WDS bridging? It is generally used in a large area, a wireless router with limited signal coverage, making certain areas of the site without signal or weak signal; This can add a wireless router and configure the WDS bridge to allow wireless WiFi coverage throughout the site. To set the method for Tp-link tl-wr742n router WDS bridging Warm tip: F

The network cable is connected to the router corresponding led but does not light how to do? L Check whether both ends of the network cable are connected to the correct port and plugged in; L Check whether the device at both ends of the cable is powered on; L try to change a new network cable; L try to connect the device to another port on the router. L Check to see if the SYS lamp for the

solve the Tp-link router 5G signal Search method One, confirm whether the router supports 5G band Possible causes: Wireless routers do not support 5G bands. Workaround: Please check the wireless router's product specification or the consulting equipment manufacturer to verify that the wireless router supports the 5G band. If the Tp-link wireless

A DOS dictionary attack on a router can allow an attacker to gain access to the Cisco router or may cause the user to be unable to use the router. In this article, you can find out how to use the enhanced login capabilities of the Cisco network operating system to prevent this attack. You may not have realized that using a dictionary denial of service (DoS) atta

Routers are a must-have for multi-user shared Internet access and the main source of WiFi signals At present, home routers are equipped with WiFi, so many users can not tell what is the WiFi password what is the management password, now detailed information about the router's various accounts and passwords 1. Router Administrator account and password Router and Win7 operating system, there is an administ

For the Cisco router security configuration command family, the following are 10 configuration commands, which are expected to be good for everyone. When talking about configuring a new Cisco router, most configurations depend on the type of the router and the purpose of the service. However, each administrator has his/her own command list for configuring each

The author recently installed Windows 7 for the computer, but found that it could not log on to any Web page with IE. Look at the connection status of the wireless router and find that the signal is strong but it cannot connect successfully. The WPA wireless password you set is changed, so you reset it and still cannot connect successfully. The wireless encryption is then canceled, but the result is still unable to connect. Has the wireless

For the router protocol this term, probably many people have been familiar with, especially the current network development quickly, Internet Router Protocol is also constantly improving, but also appeared a lot of new features. The wide application of information technology in various fields has promoted the rapid development of information exchange network, in which the Internet is the biggest beneficiary