vmware workstation trial

network segment, the NAT router is only used for the address segment that is governed by NAT, so 192.168.222.1 does not fall within the jurisdiction of this Gateway.So the host wants to pass 192.168.222.1 this network card to reach the NAT server is not feasible.Conclusion:From the routing table, the host principle packet can reach 192.168.222.2 this gateway, but this gateway does not give a reply, because the host's virtual network card is not the role of NAT and managed IP address.Network tes

This article by show according to Lin Feng to provide friendship sponsorship, starting in the mud row world.Because of the need to do ESXi-related experiments, you can experiment with VM virtual ESXI on your own machine. Because the experiment requires two NICs, two NICs were added when the ESXi virtual machine was created. As follows:However, the problem arises, in the installation of ESX found only one NIC. Because there was no at that time, so cannot show here. Anyway, only one NIC can be see

VMWare Workstation 6.5, installs the win Server, results in the installation process does not prompt copyright, partition and other steps, directly all disk space as the C drive, and install the system. -This is the benefit of easy install. But I want to do the partition first. Later, the problem was discovered: When you set up virtual machine, if you specify the installation options, whether it is insta

system.Iv. start the installation of the system　　To turn on the virtual machine:　　Enter　　Loading in ...　　Set Language, Chinese　　Click on the installation location with an exclamation point (if no exclamation mark is used), click to go to the installation location　　Click Finish　　Click to start the installation　　Click the root password to set the password (root)　　After setting the password, click Finish　　Wait for the installation process ...　　After installation, restart the system.Vi.. Login　　Aft

For later use.First step: Set up VMware's edit-virtual network editor, enable Vmnet8,nat mode, as shown in.In fact, VMware default settings, no changes, if you accidentally changed, click Restore Default settings.The second step: virtual machine settings-the network adapter, set to NAT mode, as shown in.It is also the default and does not need to be changed.Step three: Edit the network configuration file for the Linux system.Under the/etc/sysconfig/ne

Tags: online pause hat net method installation complete boot command redI downloaded a 14 virtual machine on the Internet, after the completion of the serial number after installation, then I create a new virtual machine-a typical installation-install the operating system later-linux-redhat6.5 Continue next Next individual OK turn on Virtual machine Discovery virtual machine Boot black screenThen just try to hang up is the meaning of pausing this virtual machine, and then try my method first ste

Recently to help a customer to do an offline plug-in, because the traffic limit and the number of hanging a lot so you need to use the virtual machine most shunt.The VM has been used before but found that if the host's VPN disconnection restarts after the virtual machine inside the site will take a long time to restore the network, resulting in offline time is too long.Try to use VirtualBox for this reason, and finally decide to use VirtualBox.This product is relatively simple compared to VMS, b

First, create a virtual machine1. Things to keep in mind when creating a virtual machineVirtual machine Creation I believe everyone will, the process is not detailed, said the following matters needing attention:When you create a custom type configuration, the virtual machine is different from the standard type configuration:Select virtual Machine hardware compatibility: This virtual machine can also be used by a lower version of workstation or

Tags: com time NFS ATI term ges restart disk bootVmware Workstation Installing Oracle Solaris 101, open the VMware Workstation, create a new virtual machine, type select "Typical";2, select the system version;3, configure the virtual machine name;4, select the size of the disk;5, configure the CD mount, CPU and memory;6, boot start, select the first start;7, sele

There are several steps to sharing a folder:Setting up shared folders, shutting down the virtual machine before setting up sharing (this is important)To VMware, Vm->settings:default File Share: options->shared Folders: Always Enabled:Then add the folder: Add shared folder, where you set the directory and name of the shared folders (called shared)The last step is to turn on sharing: enable this shareOpen the virtual machine to detect if our shared modu

Fedora16x86_64 installation VMware-Workstation-Full-7.1.5-491717.x86_64.bundle-Linux general technology-Linux technology and application information, the following is read details. Fedora 16 x86_64 VMware-Workstation-Full-7.1.5-491717.x86_64.bundle Installation Prompt installation of the Eclipse C/C ++ Remote Debuggin

The installation and configuration of virtual machines have been studied in the past few days. However, the network settings of these virtual machines are a little difficult (except that the virtual machines can only access the Internet through NAT. The following are some ways to share files between hosts and virtual machines on the Internet! Share with you The test environment is: Physical Machine:Win XP SP2 patch all systemsVirtual Machine version: VMware