windows iot dashboard for windows 7

1, we first enter into the Win7 system so first to let it automatically upgrade to the WIN10 function to cancel, the specific operation as follows; 2, click "Run" in the Start menu and enter "Gpedit.msc" to open the system "local Group Policy Editor" as shown in the following figure; 3, the Operation Gpedit.msc as shown below, again disable the above policy settings; 4, open the Computer Configuration-Administrative Templates-Windows Componen

Failure phenomenon: It is not customary to use the new WIN8 system to install the Win7 system, but the system cannot be partitioned during the installation Win7 process. Tip Windows cannot install to this disk. The selected disk has an MBR partition table. On the EFI system, Windows can only be installed to a GPT disk. ” Reason Analysis: This machine uses the EFI motherboard, with the WIN8 operating sys

Windows operating system logs when a hard disk suddenly loses disk in windows 7Environment: three desktop hard disks (sata3 Interface) are connected to the same desktop without raid, one of which is hard disk (Note: Not a partition) suddenly disappears from "Computer Management"-"disk management". Of course, the partition of this hard disk (a partition in ntfs format was previously created) also disappears

First, host WINDOWS7 system setup 1. Install the WIN7 printer driver first. Shut down the system firewall. Turn off system firewall: Go to Computer "control Panel" → " windows firewall" → "Turn on or off windows firewall" → "Shut down firewall". 2. Click on the lower left corner of the computer "start" → "devices and printers"-Find th

The first thing we need to know about the role of folders on Windows 7 is that Windows 7 does not occupy that much space. In addition to including virtual memory and other files, Windows 7 also ensures smoother system usage. Of co

Now a lot of people in the installed is a habit, if the system installed in the C, then the software will be loaded into the D disk, e-disk and other non-system disk. But the general software in the installation, the system will be the default path set to C:/Program files/xxxx, and if the above idea, each software will have to select a path, there is no shortcut? Do you have? *win+r Run Regedit open Registry Editor * Locate to HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\

Should be part of Bo friends, this and the next several elaborated on the use of WDS to advertise the operating system, that is, network installation Win7 systems. Preparation is necessary, WDS roles and DHCP are installed as an underlying environment in this article, the WDS role provides WDS services, DHCP provides DHCP to enable clients to obtain IP from the network startup and then obtain the boot image and read the image, and then start the Win7 installation. Master and cattle skip this art

If you are using an operating system that is WIN7 or Windows Vista version, you will use the sidebar gadget. One day, a friend asked me how this sidebar gadget is made, I checked, this thing is actually divided into two types of gadgets, one is called "Sidebar gadget sidebar", there is a call "SideShow", and the use of development technology is not the same, The former you can only a little bit of web development technology can, the latter requires a

1. Press "Win+r" and enter Gpedit.msc carriage return successfully entered the Group Policy Editor. 2. In the Group Policy Editor that goes into, we click "Computer Configuration"--"Administrative Templates"--"Windows Components" and then we click on the left window to find the Windows Media Player item and expand. 3. Here we find "Prevent Automatic Updates" and double-click to open, then we s

As shown in the following figure, we are prompted "Windows detects a hard drive problem" error The solution is shown below 1, Boot press F8 or del into the BIOS, and then we use the BIOS to detect the hard drive is not a problem 2, if you confirm the hard drive detection is normal, in the computer we right-click the partition letter, such as D disk and then click "Properties" in the pop-up menu, then we click on the "Tools" tab, in the Entry inte

First step, BIOS setup A, enter the BIOS interface, select "Exit" → "Os Optimal default" set to "Disabled" (OS Optimal default switch can be understood as UEFI and traditional BIOS switching) B, press the F9 on the keyboard to restore the BIOS defaults C, enter the startup interface, set "CSM" as "Enabled" (CSM: Compatible support modules Compatibility Support module) D, startup interface, set "Boot Mode" for "legacy only"; Press F10 to save the exit. Step two, install the system You must

up the domain Name System (DNS). To be able to use single label names, many networks have deployed Windows Internet Name Service (WINS) technology and WINS servers in their environments. As a name Resolution Protocol, WINS is an alternate option for DNS. It is an old service that uses NetBIOS (NetBT) on TCP/IP. WINS and NetBT do not support the Internet Protocol version 6 (IPV6) protocol, so they will be phased out in many networks. To help network a

1, we just right click on the desktop "Start Menu" and then open the window click "Control Panel" to enter after we find "user and home security, and then click User Account"; 2, then we find the interface of the "Change user Account Control settings" option; 3, move the slider to never notify, and then apply exit. All right, you're not going to see Win7 after this setup. Running Setup appears to block windows

1. We suspect a network configuration problem, try to modify the WINDOWS2003 network adapter configuration: Right click on the desktop "Network Neighborhood" and then click on the properties, go to the "Internet connection" page we will see a "local connection" we then right-click it, click "Properties" pop-up "local connection Properties" as shown in the following image. Then we click "Configure" in "Local Connection Properties", as shown in the following image, so that in the pop-up dialog

Our TMG basically work normally, this article we try to play in 2008r2 and Win7 This environment, this series writes to now, we should have all seemingly have, The rest is the internal and external interoperability problem. Let's take a look at this one. Publish some application and setup strategies look at the difference between the tmg2010 and isa2006 versions. We add computers to the computer group, seems to be no different from before, or can only add IP to identify the computer to set perm

As the size of the company expands, NS1 has been unable to meet the company's increasing file-sharing needs So the purchase of a new host Xeon 5500,2G memory, Gigabit network card, 2TB hard disk backup First install the machine Windows Server 2008 SP2, this example does not install 2008R2, to see what is different, and the NS1 on the sharing of the perfect migration to the new file server, security permissions are not lost. In fact, the best way is

Install CentOS 7 and centos with a USB flash drive on Windows 7 If you already have Windows 7, you have to install CentOS 7 again.1. Divide disk space Separate the installation space for CentOS

://s2.51cto.com/wyfs02/M00/95/0D/wKioL1kRSHDjAUXDAADzz4cAeZQ522.jpg "style=" float : none; "title=" 4.JPG "alt=" Wkiol1krshdjauxdaadzz4caezq522.jpg "/>Let's take a look at the physical machine: since we have a different partition format for Linux and Windows, we leave some room for liunx. This Windows 7 is already installed and the primary partition is in drive C

What do you need to pay attention to when backing up Ghost for Windows 7 7?Ghost is an essential tool in the installation system and can be used to quickly back up and install the system. Traditional applications of Ghost Software to Windows XP are common, but when using Windows