wrt54g firmware

Next I will show you how to upgrade the router firmware to the latest Tomato version, and then configure the Quality of Service (QoS) to manage network traffic. Third-party routing software has been released for a while, but we do not have to recommend these products to users who want to add new features to the home network. Our favorite router firmware package is still Tomato, because it provides good comp

) unlocked03.10.01 (IOS 4.2.1) unlocked 3gs 06.15 the baseband network says it cannot be navigated, and it has never succeeded. However, you are skeptical about navigation. The final conclusion is: 1. I do not know whether it is related to the baseband. 2. The navigation function is related to whether satellite signals can be received. Solution: 1. Install the navigation software. 2. Use baseband 05.13.04 (not sure whether 06.15 can be navigated) 3. Install the GPS kit pa

that the AP in the relay mode accepts connections from other wireless network devices in addition to signals from other APs.Figure 2 shows the WDS setting interface for LinkSYS WRT54G (DD-WRT Firmware), available in "LAN" and "Point to Point" modes. As the name suggests, LAN is the Repeater mode. The WDS network can receive connections from other wireless devices, while the Point to Point is the Bridge mod

A few months ago started a turn of the WNR3500L, this route known as open source and third-party firmware support is very attractive to me, first began to brush the DD-WRT and then changed to TOMATO, after switching to TOMATO, connect to the route through ssh. ifconfig shows a lot of interfaces, except for familiarity... A few months ago started a turn of the WNR3500L, this route known as open source and third-party

provided is ppp0, which is equivalent to vlan1.You can refer to the figure below (although it is for wrt54g, but it also applies to 3500L) to understand the above section:For details about the logic view, refer to the following:The eth0 does not exist. Because the eth0 interface is not used, the system directly uses vlan0, vlan1, and ifconfig derived from eth0. Of course, vlan0 and eth1 are also used in the form of br0. The lan ip address we allocate

figure below (although it is for WRT54G, but it also applies to 3500l) to understand the above section: For details about the logic view, refer to the following:The eth0 does not exist. Because the eth0 interface is not used, the system directly uses vlan0, vlan1, and ifconfig derived from eth0. Of course, vlan0 and eth1 are also used in the form of br0. The lan ip address we allocate in the route is actually allocated to br0. If pppoe is used for di

Summarize the OpenWrt start-up process: 1.cfe->2.linux->3./etc/preinit->4./sbin/init->5./etc/inittab->6./etc/init.d/ Rcs->7./etc/rc.d/s*->8.OpenWrt is an open Linux platform, primarily for WiFi-free overhead. Similar to the Linux distributions of Ubuntu, Red Hat, and so on, it also has its own start-up process. Below, I will take my Linksys WRT54G for platform Introduction, OPENWRT START process. First of all, CFE (common

multicast mtu:1500 hop count: 1Receive packet: 295308 Error: 0 Discard: 0 Overload: 0 Number of frames: 0Send packet: 208860 error: 1 Discard: 0 Overload: 0 Carrier: 0Collisions: 0 Send Queue Length: 1000Receive bytes: 394951279 (394.9 MB) Send bytes: 19510963 (19.5 MB)Lo Link encap: local loopbackinet Address: 127.0.0.1 Mask: 255.0.0.0Inet6 Address::: 1/128 scope:hostUp LOOPBACK RUNNING mtu:65536 metric: 1Receive packet: 943526 Error: 0 Discard: 0 Overload: 0 Number of frames: 0Send packet: 94

packet: 943526 error: 0 Discard: 0 Overload: 0 Carrier: 0Collisions: 0 Send Queue Length: 1Receive bytes: 464924375 (464.9 MB) Send bytes: 464924375 (464.9 MB)2. Use the LSHW command to output information (only the information related to the wireless card is posted) as follows:[Email protected]:~$ lshw*-network DISABLEDDescription:wireless interfacePhysical Id:2Logical Name:wlan0 1Serial:92:31:e3:4a:75:f2Capabilities:ethernet Physical WirelessConfiguration:broadcast=yes driver=brcmsmac driverve

or bridging function of the wireless router to enlarge the signal. Selection of wireless routers Common wireless routers do not have the relay mode, but can be implemented by refreshing third-party firmware. If dualwan Dual Network is required, it is best to purchase a wireless router without dualwan tomato, that is, the wireless router using the Broadcom chip, the most common is the Linksys WRT54G

: 0 overload: 0 frames: 0Send data packets: 943526 error: 0 discard: 0 overload: 0 carrier: 0Collision: 0 sending queue length: 1Received byte: 464924375 (464.9 MB) sent byte: 464924375 (464.9 MB) 2. Use the lshw command to output the following information (only information about the wireless network adapter is attached: Jello @ jello :~ $ Lshw *-Network DISABLEDDescription: Wireless interfacePhysical id: 2Logical name: wlan0 1Serial: 92: 31: e3: 4a: 75: f2Capabilities: ethernet physical wireles

equivalent to a check box with three states, and string is equivalent to a text edit box for the user to enter a string, hex is equivalent to a text editing box that allows users to enter hexadecimal numbers, while int is equivalent to a text editing box that allows users to enter integer numbers. Type keywords can follow the prompt characters or do not follow, depending on the situation. For example: string "path to uevent helper" bool "Prevent firmware