[Abstract] Windows 7 hard drive Installation Method

Not all computers are equipped with DVD Rom, which makes it difficult to install Windows 7 on the computer. Windows 7 cannot be installed on the optical drive, or you can use a USB flash drive to install Windows 7. However, USB flash drives are not supported by all computers. You can only use the hard disk installation method. Before that, XP and Vista can directly use the virtual optical drive to mount the system image for installation. However, win7 does not support this method. Hard Disk installation is a little troublesome. Today, I just helped my friend install win7 in his laptop (with a fault in the optical drive). After trying, it was not too difficult to install the hard drive. If you do not have a DVD drive on your computer, try win7 again! 1. Install the High Version Windows 7 in Windows 7: 1. Download the Windows 7 7600 ISO image (RC or RTM ), use a virtual optical drive to load images and select all folders and files and copy them to a non-C drive (for example, D: \ 7600) 2. Press F8 to fix the system and select the last command to fix the system. Enter "D: \ 7600 \ sources \ setup.exe" in the Command box (without quotation marks) 3. Enter the installation interface, select Custom for installation 4. Select the installation language, format the C drive 5, and OK. After installation, it is a pure system (non-Dual System ). 2. If there is a vista installation disk, the method is also very simple: 1. Download the Windows 7 7600 ISO image, use the virtual optical drive to load the image, select all the folders and files, and copy them to a non-C disk (such as D: \ 7600) 2. Select Drive boot in BIOS to go To the Vista installation page. 3. Select repair computer in the lower left corner. (The system is automatically searched, and the system prompts you to load or disable the driver. Select disable to enter the repair option) 4. Select the last command for restoration. In the command box, enter "D: \ 7600 \ sources \ setup.exe" (without quotation marks ), start installation 5. Select the installation language and format the C drive (even if the C drive does not have a system) 3. Install Windows 7: 1 on the Windows 7 7600 ISO image on the Windows XP system, use a virtual optical drive to load the image, select all folders and files, and copy them to a non-C drive (such as D: \ 7600). 2. Copy D: \ 7600 directory bootmgr and boot directory (in fact, as long as the boot. SDI and BCD files) copy to the C root directory, and create s under the C root directory Ources folder. (You do not need to obtain administrator permissions in XP) 3. Run the boot command in D: \ 7600 \ sources. copy win to the Sources folder created on drive C. 4. Run cmd as an administrator. Then enter c: \ Boot \ bootsect.exe/nt60 C: the prompt successful is displayed. The red part has two spaces, that is, success !) 5. Close the CMD window and restart the computer. The installation interface is automatically displayed. Select the language for installation, select the appropriate time and currency display type and keyboard and input mode. 6. The "Start installation interface" is displayed. (Note that you do not need to click "Install now ") click "repair mycomputer" in the lower left corner to go to "System Recovery selection", select the last "command prompt" (commandprompt), and enter the DOS window 7. Enter "D: \ 7600 \ sources \ setup.exe "(without quotation marks), start installation 8. Select the installation language and format the C drive, 4. Install Windows 7 in the Vista system (it is proved that XP is more convenient to use this method): 1. Download the Windows 7 7600 ISO image, use a virtual optical drive to load the image and select all folders and files and copy them to a non-C drive (such as D: \ 7600). 2. Copy D: the boot, EFI, and sources folders in the \ 7600 folder and bootmgr to the c drive root directory 3. Copy D: \ 7600 \ Boot Run cmd as the administrator and enter c: \ bootsect.exe/nt60 C: And press enter (it is recommended to copy, the red part has two spaces) 5. restart the system to automatically enter the installation interface. Click repair computer repair my computer in the lower left corner. 6. Select the last command prompt, enter the DOS window, and enter D: \ 7600 \ sources \ setup.exe enter the installation interface 7. Select the installation language and format the C drive. 5. Installation Method in the PE system: 1. Download the Windows 7 7600 ISO image, use a virtual optical drive to load the image and select all folders and files and copy them to a non-C drive (such as D: \ 7600). 2. Format: C, NTFS. 2. Put the bootmgr and boot directories under the D: \ 7600 directory (in fact, as long as the boot. SDI and BCD files) are copied to the C root directory, and a Sources folder is created under the C root directory. 3. Run the boot command under D: \ 7600 \ sources. run CMD and enter c: \ Boot \ bootsect.exe/nt60 C: prompt successful (that is, success !) 5. Close the CMD window, restart the computer, automatically enter the installation interface, and select the installation language, select the appropriate time and currency display type and keyboard and input mode. 6. The "Start installation interface" is displayed. (Note that you do not need to click "Install now ") click "repair mycomputer" in the lower left corner to go to "System Recovery selection", select the last "command prompt" (commandprompt), and enter the DOS window 7. Enter "D: \ 7600 \ sources \ setup.exe "(without quotation marks), start installation 8, select the installation language, format the C disk, OK