Adsl modem initial address and user name and password

Adsl modem initial address and user name and password
To debug these settings, You need to first set the IP address of the network card to the same network segment as the ADSL settings.
1. In the address bar of the IE browser, enter the IP address 10.0.0.2 in the omnidirectional QL1680. The username is the default value when the admin leaves the factory: the password is qxcomm1680, And the administrator password is

Qxcommsupport
2. In the address bar of IE browser, enter the IP address 192.168.1.1 in the omnidirectional QL1880. the user name is root, and the default value is root.
3. In the address bar of IE browser, enter the IP address 10.0.0.2 and the user name is admin. The default value is qxcomm1688.
4. CyberLink 6307/6309 uses dslcom.exe in the optical drive with Cyberlink6307/6309kg. the default value is: Route IP Address: 192.168.1.1 password.

: Stm
5, TP-LINK TD-8800 in IE enter 192.168.1.1, Account Name admin, password admin.
6. Run zyxel 642 and enter telnet 192.168.1.1 password 1234. Press and hold the RESET key next to the fuselage and start the instance. The factory default value can be restored after dozens of seconds.

Value.
7, Ecom ED-802EG in IE enter 192.168.1.1, the user name and password are root
8. shenzhou.6010ra: Enter the username of 192.168.1.1 in IE as ADSL and the password as ADSL1234.
9. The initial IP address of the Huawei SmartAX MT800 is 192.168.1.1, And the username and password are both ADMIN. There are two methods to restore the default configuration: one is to continuously press the RESET key three behind the MODEM.

In the configuration menu, choose SAVE & REBOOT to restore the default configuration.

Ittek
Http: // 192.168.1.1/
User name: supervisor
Password 12345

ASUS
Http: // 192.168.1.1/
Username: adsl
Password: adsl1234

Alcatel
Http: // 192.168.1.1/
Generally no password

Same-dimension DSL699E
Http: // 192.168.1.1/
Username: ROOT
Password: ROOT

Daya DB102
Http: // 192.168.1.1/
Username: admin
Password: dare
Advanced Settings page:Http: // 192.168.1.1/doc/index1.htm
RT1080 of WST
Http: // 192.168.0.1/
Username: root
Password: root

WST ART18CX
Http: // 10.0.0.2/
Username: admin
Password: conexant
Username: user
Password: password

Omnidirectional qxcomm1688
Http: // 192.168.1.1/
High-end password: qxcommsuport

Omnidirectional qxcomm1680
Http: // 192.168.1.1/
The password used to log on to ADSL is qxcomm1680.

Shida
V3.2 root
Root
V5.4 root
Grouter

FUDE
Admin
Conexant

Easten Ea700
Http: // 192.168.1.1/
Username: NULL
Password: password

Broadmax hsa300a
Http: // 192.168.0.1/
Username: broadmax
Password: broadmax

Changhong ch-500E
Http: // 192.168.1.1/
Username: root
Password: root

Chongqing Putian CP ADSL03
Http: // 192.168.1.1/
Username: root
Password: root

* ** Break through EA110
RS232: 38400
Http: // 192.168.7.1/
UsernameSL
PswSL

ADSL_T07L006.0 of etek-td
Http: // 192.168.1.1/
User Name: supervisor
Password: 12345
Solution to password loss:
Use the Xmodem method of the Super Terminal to rewrite Vxworks. dlf and restore the password to: 12345.

GVC DSL-802E/R3A
Http: // 10.0.0.2/
Username: admin
Password: epicrouter
Username: user
Password: password

Kemaiyi Tong km300A-1
Http: // 192.168.1.1/
Username:
Password: password

Kemaiyi Tong km300A-G
Http: // 192.168.1.1/
Username: root
Password: root

Kemaiyi Tong km300A-A
Http: // 192.168.1.1/
Username: root or admin
Password: 123456

Sunrise's SR-DSL-AE
Http: // 192.168.1.1/
Username: admin
Password: 0000

Sunrise's DSL-802E_R3A
Http: // 10.0.0.2/
Username: admin
Password: epicrouter
Username: user
Password: password

UTStar's ut-300R
Http: // 192.168.1.1/
Username: root or admin
Password: utstar

These are the default initial IP addresses, user names, and passwords for the factory of ADSL, which must be known for debugging.

There are three methods to debug these settings. One of the most common WEB methods is to fill in the IP address set up in the browser, such as QX1680.

Enter 10.0.0.2 in the address bar of the browser. In the prompt bar, enter the username admin and password qxcommsupport to set the administrator interface. This is the most common and simple method.

Method.

The second method is to use TELNET to telnet the IP address, such as the early co-operation 642.
192.168.1.1, and then enter the password 1234 to enter the English character interface.

The third method is to use the vendor's own configuration program to enter the configuration interface, such as CyberLink 6307/6309
It uses dslcom.exe in the optical disk with Cybrlink 6307/6309 kg,
Factory default value: Route IP Address: 1 92.161.1 password:
Stm, because this method is not as convenient as the first two methods, it is rarely used in low-end products.

Debugging of most products requires that the dual-wire connection of the product be used first, and then the IP address of the NIC of the local machine be set to the same network segment as this one.

And then configure. If the default IP address or password is changed, most of them can be reset to restore the default value. The most common and useful method is to set up a power failure

Press and hold the reset key, and then power on. After a short period of time, the default factory value can be restored.

Article entry: aaadxmmm responsible editor: aaadxmmm