Basic VOIP Configuration

Tutorial description:
In this experiment, two Cisco 2600 vrouters and one Cisco 3600 vro are used to implement Voip for Division 1 and Division 2 of the blue school. The two Divisions use Cisco's 2620 as the terminal device, and the Headquarters uses Cisco's 3640 router as the center networking device. The specific structure of the connection between the leased lines is as follows:
Branch 1)
Cisco 2600 Voip configuration
Current onfiguration
!
Version 12.0:
Service timestamps debug uptime
Service timestamps log uptime
No service password-encryption
!
Hostname bluestudy1
!
Enable password Cisco
!
Ip subnet-zero
!
Voice-port 1/0/0
Time-port call-disconnect 0
!
Voice-port 1/0/1
Time-port call-disconnect 0
!
Voice-port 1/1/0
Time-port call-disconnect 0
!
Voice-port 1/1/1
Time-port call-disconnect 0
!
Dial-peer voice 1 pots
Destination-pattern 1234
Port 1/1/0
!
Dial-peer voice 10 voip
Destination-pattern 4321
Session target ipv4: 199.1.2.2
!
Interface Ethernet0/0
No ip address
No ip directed-broadcast
Shutdown
!
Interface serial0/0
No ip address
No ip directd-broadcast
Encapsulation frame-relay
No ip mroute-cache
Frame-relay lm-type ansi
!
Interface serial0/0.1 point-to-point
Ip address 199.1.1.2 255.255.255.255.248
No ip directed-broadcast
Frame-relay interface-dlci 111
! Interface ethernet0/1
No ip address
No ip directed-broadcast
Shut down
!
Interface serial 0/1
No ip address
No ip directed-broadcast
Shut down
!
Interface serial0/2
No ip address
No ip directed-broadcast
Shut down
!
Interface serial0/3
No ip address
No ip directed-broadcast
Shut down
!
Router rip
Version 2
Network 199.1.1.0
!
Ip classless
No ip http server
!
!
Line con 0
Transport input none
Line aux
Line vty 0 4
Password cisco
Login
!
No scheduler allocate
End
For the configuration of 3640, it is used to simulate that the ISP only needs to configure the corresponding address on its wide-area port, use 199.1.1.1 255.255.255.248 to connect to the branch 1, and configure the port address to 199.1.2.1 255.255.255.255.248, configure the route and start the rip two protocol in the 199.1.1.0 and 199.1.2.0 networks.
Division 2
Cisco 2600 Voip configuration
Current configuration
!
Version 12.0:
Service timestamps debug uptime
Service timestamps log uptime
No service password-encryption
!
Hostname bluestudy2
!
Enable password Cisco
!
Ip subnet-zero
!
Voice-port 1/0/0
Time-port call-disconnect 0
!
Voice-port 1/0/1
Time-port call-disconnect 0
!
Voice-port 1/1/0
Time-port call-disconnect 0
!
Voice-port 1/1/1
Time-port call-disconnect 0
!
Dial-peer voice 1 pots
Destination-pattern 4321
Port 1/1/0
!
Dial-peer voice 10 voip
Destination-pattern 1234
Session target ipv4: 199.1.1.2
!
Interface Ethernet0/0
No ip address
No ip directed-broadcast
Shutdown
!
Interface serial0/0
No ip address
No ip directd-broadcast
Encapsulation frame-relay
No ip mroute-cache
Frame-relay lm-type ansi
!
Interface serial0/0.1 point-to-point
Ip address 199.1.2.2 255.255.255.255.248
No ip directed-broadcast
Frame-relay interface-dlci 111
! Interface ethernet0/1
No ip address
No ip directed-broadcast
Shut down
!
Interface serial 0/1
No ip address
No ip directed-broadcast
Shut down
!
Interface serial0/2
No ip address
No ip directed-broadcast
Shut down
!
Interface serial0/3
No ip address
No ip directed-broadcast
Shut down
!
Router rip
Version 2
Network 199.1.2.0
!
Ip classless
No ip http server
!
!
Line con 0
Transport input none
Line aux
Line vty 0 4
Password cisco
Login
!
No scheduler allocate
End