Beiyang btp-2200e Barcode Printer label Paper Carbon Tape installation

　　Beiyang btp-2200e is a powerful barcode printer, used for various sales of barcode printing work, before using the need to install Beiyang btp-2200e Barcode Printer label paper and installation, and then you can remotely install the printer driver, After installation can use Beiyang Barcode printer, the following Shenzhen trust constant technology to teach you how to install and install the machine!

　　First, the carbon tape installation steps

1, remove the carbon belt mandrel and ribbon, according to the direction shown in the following figure, the carbon belt mandrel inserted into the carbon belt axis; The ribbon is circled as shown in the following image;

2, according to the diagram arrow direction of the hands to push the printer to turn upside down, open the printer's upper lid;

3, downward press the print head to lift the button, lift up the carbon belt support frame (30° about the angle, hear a slight "pop" hint sound, the carbon belt support frame will maintain this position not to move);

4, the Carbon belt distribution shaft of the manual pull sleeve outward light pull, the carbon belt release shaft shaft to the left to the distribution of the shaft dial hexagonal convex taichung;

NOTE: The Ribbon release shaft left groove must be with the distribution of the shaft dial hexagonal convex platform mesh well, otherwise the printer may alarm lack of ribbons.

5, the Carbon belt release axis to the right side of the manual pull sleeve of the plug, loosen the manual pull sleeve, release shaft carbon tape installation completed;

6, take out another carbon belt mandrel and Carbon belt recovery paper shaft, as shown in the following figure, the carbon belt mandrel inserted into the belt recovery paper shaft;

7, the manual pulling sleeve of the belt recovery shaft is pulled outward, and the carbon belt recovery shaft is inserted on the left side of the recovery shaft, and the hexagonal convex table of the recycling axle is arranged, the right side of the belt recovery shaft is aligned with the plug of the manual drawing sleeve, and the belt recovery shaft is installed;

8, from the installed carbon belt release shaft to remove the Ribbon front-end, the Ribbon front-end from the bottom of the print head to bypass, and then the Ribbon front-end part of the tape to be installed on the tape recovery shaft on the paper axis;

9, move the carbon belt to rotate the wheel, so that the ribbon wound in the carbon belt recovery shaft and tighten the carbon belt, so far, the carbon tape installation finished.

Attention:

1, the installation of carbon with a toner side downward;

2, the installation process to avoid the carbon belt wrinkling;

　　Second, the label paper installation

1, in accordance with the order shown in the following figure, first of all, a forced cardboard inserted into the paper roll support rod, the paper roll supporting rod inserted into the paper reel, another force paperboard inserted in the paper roll support rod, and pay attention to make the paper roll and the two sides of the cardboard has a certain gap

2, will be installed in the paper roll support rod paper roll into the paper bin, the installation process to pay attention to the support rod at both ends of the projection, into the bar code printer on both sides of the paper warehouse groove;

3. Pull the paper front end out of the print channel of the barcode printer, and the front end is flush with the paper mouth of the printer, with the left and right force paper block will pull out the paperclip;

Note: If you use Black Label paper, put the black mark down, and you want to be on the reflection sensor!

4, press down the carbon belt support frame to the locking state, so that the paper installed, as shown in the following figure.

　　Third, printing settings

1, first the printer USB data cable connected to the computer, install printer driver: The following figure:

2, directly click Next operation for Typical installation. Port Select "Usb-2200e_1" until the printer driver installation is complete.

3, printer settings: Right-click Printer-Properties, General tab, click on the bottom of the "printing preferences"-action tab, set as follows

4, in addition, the replacement of carbon belt, the need for the right paper, the correct operation is, suspend the key + Power-on key after the need to press the feed key, to see whether the normal out of a line of paper.

　　Attention matters

The printer needs to be debugged according to normal settings

If you do not solve your problem, directly contact the printer's suppliers, or Shenzhen, Shenzhen, mutual trust and constant technology company website to obtain the barcode printer installation video, parameters, and Beiyang Barcode printer quotes and other information, and can get the corresponding technical support!