BIOS in Chinese and English table _ Installation Tutorial

Time/system Time/system times
Date/system Date/System dates
Level 2 Cache Two buffer
System Memory Systems Memory
Video Controller Controller
Panel type LCD Screen model
Audio Controller Audio Controller
Modem Controller Modems
Primary Hard Drive Primary Hard drive
Modular Bay Module Bay
Service tag Tag
Asset Tag Asset Tag
BIOS Version BIOS revision
Boot order/boot Sequence boot sequence (System searches the order of operating system files)
Diskette Drive Floppy disk drive
Internal HDD Built-in hard drive
Floppy Device Floppy drive device
Hard-disk Drive Hard Drive
USB Storage Device USB storage device
CD/DVD/CD-RW Drive Optical Drive
CD-ROM device optical drive
Modular Bay HDD Modular Hard Drive
CardBus NIC CardBus Bus network adapter
Onboard NIC onboard network card

Boot POST
The level of the hardware check at post: set to "minimal" (default setting) The post is checked only for BIOS upgrades, memory module changes, or previous power-on self-test. Set to "thorough" performs a full set of hardware checks at post.

Config warnings
Warning Setting: This option is used to set whether to alert if the system uses a lower voltage power adapter or other unsupported configuration, set to "DISABLED" Disable alerting, set to "enabled" enable alerting

Internal Modem
Built-in modems: Use this option to enable or disable the built-in modem. The modem is not visible in the operating system after disabling (disabled).

LAN Controller
Network controller: Use this option to enable or disable the PCI Ethernet controller. When disabled, the device is not visible in the operating system.

PXE bis Policy/pxe bis Default Policy
PXE BIS Policy: This option controls how the system handles (starts the overall service boot Integrity services (BIS) licensing request without authentication. The system can accept or reject bis requests. When set to reset, the BIS is reinitialized and set to "Deny" the next time you start your computer.

Onboard Bluetooth device
MiniPCI Device Mini PCI Device
MiniPCI status Mini PCI device state: You can use this option to enable or disable onboard PCI devices when installing mini PCI devices

Wireless Control
Wireless control: Use this option to set the control mode for MINIPCI and Bluetooth wireless devices. When set to application, a wireless device can be enabled or disabled by an application such as "Quickset", and the hotkey is not available. When set to "/application", wireless devices can be enabled or disabled by applications or hotkeys such as "Quickset". Wireless devices are disabled when set to "Always off" and cannot be enabled in the operating system.

Wireless
Wireless devices: Use this option to enable or disable wireless devices. This setting can be changed through the "Quickset" or "hotkey" in the operating system. Whether this setting is available depends on the settings for "Wireless control."

Serial Port serial port: This option can be used to avoid device resource conflicts by reassigning the address or disabling the port.
Infrared data port IR. Use this setting to avoid device resource conflicts by Reassigning port addresses or disabling ports.

Parallel Mode
and the port mode. The control computer parallel port works as "normal" (at compatible) (normal standard parallel port), "Bi-directional" (PS/2 compatible) (bidirectional mode, allowing bidirectional communication between host and peripheral) or "ECP" (Extended capabilities Ports, extended function port (default).

Num Lock
Digital lock. Sets whether the digital light (numlock LED) is lit when the system starts. Set to "DISABLE", the digital lamp is kept out, set to "ENABLE" in the system when the starting point of the digital light.

Keyboard NumLock Keyboard Digital Lock: This option is used to set whether a keyboard-related error message is prompted when the system starts.

Enable keypad
Enable keypad: Set to by NumLock enable the numeric keypad when the NumLock light is lit and the external keyboard is not connected. Set to only by key keeps the embedded key area disabled when the NumLock light is lit.

External Hot Key
External hotkey: This setting allows you to use keys in the same way that you use the keys on your laptop computer on the PS/2 keyboard. If you use an ACPI operating system, such as Win2000 or WinXP, the USB keyboard cannot use the key. Keys are available only in pure DOS mode for USB keyboards. Set to SCROLL LOCK (default option) to enable this feature, set to "not installed" to disable this feature.

USB emulation
USB emulation: Use this option to use a USB keyboard, USB mouse, and USB floppy drive in an operating system that does not directly support USB. This setting is automatically enabled during the BIOS boot process. When this feature is enabled, emulation continues to be active when the control is transferred to the operating system. Disabling this feature simulates shutdown when control is transferred to the operating system.

Pointing Device
Pointing device: The external serial port mouse is enabled and the integrated touchpad is disabled when set to "Serial MOUSE". When set to PS/2 MOUSE, the integrated touchpad is disabled if an external PS/2 mouse is installed. When set to touch PAD-PS/2 MOUSE (the default setting), you can switch between the mouse and the touchpad if you have an external PS/2 mouse. Changes take effect after the computer restarts.

Video expansion
Video extensions: Use this option to enable or disable video extensions, and adjust the lower resolution to a higher, normal LCD resolution.

Battery Battery
Battery Status Battery State
Power Management Management
Suspend mode suspend pattern
AC power Recovery AC restore: This option can be reflected by the computer when the AC power adapter is plugged back into the system.
Low power mode: This option is used to set the amount of power that the system uses when it sleeps or shuts down.
Brightness
Brightness: This option sets the brightness of the display when the computer starts. The computer works in the power supply state with the default setting of half. The computer works the most by default when the AC power adapter is powered up.

Wakeup on LAN
Network wakeup: This option setting allows the computer to wake up from hibernation when the network signal is connected. This setting is not valid for machine status (Standby state). The standby state can only be awakened in the operating system. This setting is only valid when an AC power adapter is connected.

Auto on Mod
Automatic boot mode: Note This setting will not take effect if the AC adapter is not plugged in. This option sets the computer's automatic boot time, and you can set the computer to boot automatically on a daily basis or only on weekdays. Setting takes effect after the computer restarts.

Auto on time
Automatic boot time: This option can set the system to automatically boot time, the time format is 24 hours system. Type a value or use the left and RIGHT arrow keys to set the value. Setting takes effect after the computer restarts.

Dock Configuration Docking Station configuration
Docking Status Docking station

Universal Connect
Generic interface: This setting is invalid if the operating system is WinNT4.0 or earlier. If you frequently use more than one Dell docking station device, and you want to minimize the initial time of the docking station, set to ENABLED (the default setting). Set to DISABLED if you want the operating system to generate a new system settings file for each new dock device that your computer connects to.

System security
Primary Password Master Password
Admin Password Admin Password
Hard-disk Drive password (s) hard drive password

Password Status
Password Status: This option is used to lock the system password when the setup password is enabled. Set this option to "Locked" and enable the setup password to place the system password to be changed. This option can also be used to place passwords disabled by the user when the system starts.

System Password Password
Setup Password Setup Password
Post hotkeys self-Test hotkey: This option specifies the hotkey (F2 or F12) that is displayed on the screen at Power-on self-test (POST).

Chassis intrusion
Chassis anti-theft: This option is used to enable or disable chassis intrusion detection features. When set to "Enable-silent", if chassis intrusion is detected at startup, no warning message is sent. When this option is enabled and the chassis cover is open, the field displays "detected".

Drive Configuration Drive Settings
Diskette Drive A: disk drive A: If a floppy drive is installed in the system, use this option to enable or disable the floppy disk drive
Primary Master Drive First Master Drive
Primary Slave Drive first from the drive
Secondary Master Drive Second Master Drive
Secondary Slave Drive second from drive
IDE Drive UDMA support for UDMA IDE drives: Use this option to enable or disable DMA transfers through the internal IDE hard disk interface.
Hard-disk Drive Sequence Hard Drive order
System BIOS boot devices systems BIOS boot sequence
USB Device USB Device
Memory Information Memory Information
Installed system Memory Systems Memory: This option displays the size and model of the memory installed in the system
System Memory Speed Memory rate: This option shows the rate of memory loaded
System Memory Channel mode memory Channel pattern: This option displays memory slot settings.
AGP Aperture AGP Area memory capacity: This option specifies the memory value assigned to the video adapter. Some video adapters may require more memory than the default value.
CPU Information CPU Information
CPU Speed CPU Rate: This option shows the operating rate of the CPU after startup
Bus Speed: Display processor bus speed
Processor 0 ID Processor ID: Display processor type and model number
Clock Speed Clock Frequency
Cache Size Cached Value: Displays the processor's level two cache value
Integrated Devices (Legacyselect Options) Integrated equipment
Sound Sound Settings: Use this option to enable or disable an audio controller
Network Interface Controller Network interface Controller: Enable or disable integrated network adapters
Mouse Port Mouse Ports: Use this option to enable or disable the built-in PS/2 compatible mouse controller
USB Controller USB Controller: Use this option to enable or disable the onboard USB controller.
PCI Slots PCI Slots: Use this option to enable or disable onboard PCI card slots. All PCI cards are not available when disabled and cannot be detected by the operating system.

Serial Port 1
Serial 1: Use this option to control the operation of the built-in serial port. When set to "Auto", if you use two devices on the same port address with the serial expansion card, the built-in serial port automatically reassign the available port addresses. The serial port uses COM1 first, then uses COM2, if two addresses have already been allocated to a certain port, the ports will be disabled.

Parallel Port: Built-in and port can be configured in this field

Mode
Mode: When set to ' at ', the built-in port can only output data to the connected device. When set to PS/2, EPP, or ECP mode, the data can be entered and output by the port. The protocols used in these three modes are different from the maximum data transfer rates. Maximum Transmission rate PS/2