Boot press F1 how to solve?

Boot press F1 How to solve? How to remove Boot press F1?

Have you ever encountered, every boot will appear "press F1 to Continue,del to enter SETUP", and then the screen will not jump, must first press the shortcut key F1, the computer can start normally?

Boot press F1 fault analysis?

Under normal circumstances, require the boot press F1 to enter is the system's BIOS settings have no impact on the system startup of small problems, so first check the BIOS in the hardware information settings and actual discrepancies, usually have the following situations:

1, in fact, there is no floppy drive or floppy drive is broken, and the BIOS is set up with a floppy drive, which led to the Power-on press F1 to continue.

2, the original hung two hard disk, in the BIOS set up a dual hard drive, and then took off one of the time but forgot to change the BIOS settings, will appear to boot press F1.

3, the motherboard battery does not have electricity also can cause the data to lose thereby to appear this fault.

4, reboot the system, into the BIOS setup, found that the floppy drive is set to 1.44M, but in fact there is no floppy drive in the chassis, this is set to none, troubleshooting.

Solutions for several common situations in which the boot presses F1 into the system

1. The battery on the motherboard is out of power.

WORKAROUND: Change the motherboard battery.

2, set the floppy boot, but your floppy drive has problems.

Solution: A, boot press del into the BIOS, boot boot sequence, turn off the floppy boot.

B, turn off the boot floppy detection function:

Start the computer, then press "Del" key to enter the BIOS settings main interface;

Select the "Advanced BIOS Features" setting entry and press ENTER to enter;

"Boot up floppy seek" set to "Disabled", so you can turn off the boot software detection function, and then do not need to boot press F1 started.

Boot Press F1 prompt detailed

Every time the computer boot must press F1 to start the problem of the correct solution according to the prompts, the corresponding measures adopted.

1.CMOS Battery failed

Chinese: CMOS battery failure.

Explanation: This indicates that the CMOS battery is out of power, just remove the button battery on the motherboard and replace it with a new battery. Most motherboards are using 3V button batteries, you can not buy the 5V battery back oh! You can clearly see the word "3V" on the surface of the battery by looking carefully at it.

2.CMOS Check sum error-defaults loaded

CMOS to perform all the checks found errors, to load system defaults.

Explanation: Generally speaking, it is said that the battery is almost dead, you can change the battery to try, if the problem is not resolved, then the CMOS RAM may be a problem, it is common people will not encounter, this information is mostly on the motherboard BIOS refresh is not complete will appear, The only way to do this is to refresh the BIOS, but there is no guarantee that it will succeed.

If not after a year to the Distributor to change a motherboard, after a year let the dealer back to the manufacturer to repair it!

3.Press ESC to skip memory test

Chinese: Memory check is in progress, you can press ESC to skip.

Explanation: This is because there is no skip memory in the CMOS 第二、三、四次 test, the boot will perform four memory test, of course, you can also press ESC key to end the memory check, but every time this is too troublesome, you can enter the COMs settings after the BIOS featurs setup, Set the quick power on Self test to Enabled and restart after storage.

4.Keyboard error or no keyboard present

Chinese: Keyboard error or keyboard not connected.

Explanation: Check if the keyboard connection is loose or damaged.

5.Hard Disk Install failure

Chinese: Hard drive installation failed.

Explanation: This is because the power cable or data cable for the hard drive may not be plugged in or the hard disk jumper is set incorrectly. You can check to see if the root lines of the hard drive are plugged in. Look at the two hard drives on the same root data cable settings are the same, if the same, as long as the two hard drive jumper set is not the same (one set to master, another set to slave) may also be the hard drive power cord, The data cable may not be connected or the hard disk jumper is set incorrectly.

6.Secondary slave Hard Fail

Chinese: Failed to detect from disk

Explanation: May be the CMOS settings improper, for example, not from the disk but in the CMOS set to have from the disk, then there will be errors, then you can enter the COMs settings select IDE HDD autodetection for hard drive automatic detection. It may also be the hard drive's power cable, the data cable may not be connected or the hard disk jumper settings, the solution to refer to the 5th.

7.Floppy disk (s) fail or floppy disk (s) fail (80) or floppy disk (s) fail (40)

Chinese: Unable to drive floppy drive.

Explanation: The system prompts to find the floppy drive, to see whether the floppy drive power cord and data cable is loose or wrong, or the floppy drive to another machine to try, if these are not, then have to buy another one. If you do not have a floppy drive, it is recommended that "Drive A" be set to "None" in the CMOS Setup program

8.Hard disk (s) diagnosis fail

Chinese: An error occurred while performing a hard drive diagnostics.

Explanation: This problem generally means that the hard disk itself has failed, you can put the hard drive on another machine to try, if the problem is not resolved, can only go to repair.

9.Memory Test fail

Chinese: Memory detection failed.

Explanation: Reseat the memory bar to see if it can be resolved, this problem is generally because the memory is incompatible with each other, to change a bar!

10.Override Enable-defaults Loaded

The current CMOS settings cannot boot the system, loading the preset in the BIOS to boot the system.

Explanation: Generally is in the COMs within the setting error, as long as enter the COMs settings select Load Setup defaults load the original set value and then restart.

11.Press TAB to show POST screen

Chinese: Press the TAB key to toggle the screen display.

Explanation: Some OEM manufacturers will use their own design display screen to replace the BIOS preset boot display screen, we can press the TAB key to the BIOS preset boot screen and the manufacturer's custom screen to switch between.

12.Resuming from Disk,press TAB to show POST screen

Chinese: Boot from hard drive, press TAB to show post screen.

Explanation: This is because some motherboard BIOS provides the suspend to disk (the hard drive hangs) the function, if we use suspend to disk the way to shut down, then we will display this prompt message when the next boot.

13.Hareware Monitor found an error,enter power MANAGEMENT setup for details,press F1 to Continue,del to enter SETUP

Chinese: monitoring function found error, enter the power MANAGEMENT Setup to see the details, press F1 key to continue the boot process, press del key to enter COMs settings.

Explanation: Some motherboards have the hardware monitoring function, you can set the motherboard and CPU temperature monitoring, voltage regulator voltage output and monitor the speed of each fan, when the monitoring function in the boot found abnormal conditions, then the above paragraph will appear, then you can enter the COMs settings select Power MANAGEMENT SETUP, on the right side of the **fan monitor**, **thermal monitor** and **voltage to see which part of the abnormal issue, and then resolved.

14. Display switch is set incorrectly

Chinese: Display switch configuration error

Solution: As long as your motherboard is not old, this information will certainly not appear. In general, the old motherboard has a route to set the screen to a monochrome or color. This information indicates that the settings on the motherboard are inconsistent with the CMOS setting, so just determine who is the correct motherboard and CMOS settings, and then update the wrong settings.

15. Hard disk (s) initializing (Please wait a moment ...)

Chinese: Initializing the hard disk, please wait a moment

Solution: This information is not visible at all on newer hard disks, but on older hard drives, because of the slow speed, you will see this information.