CentOS installation and configuration of minicom (serial port to USB)

Source: Internet
Author: User

CentOS installation and configuration of minicom (serial port to USB)
1. Install minicom and the file transfer Tool

Sudo yum-y installminicom lrzsz

2. Check whether your computer supports usb-to-serial communication before using the serial port. If the following words appear, OK is supported.

Lsmod | grepusbserial

Usbserial 33694 3 pl2303

3. After plugging in the usb, the connection is successful.

Dmesg | grep USB0

Check whether the device/dev/ttyUSB0 exists. If not, create one:

Ls/dev/ttyUSB0

Mknod/dev/ttyUSB0 c 188 0

4. Configure The minicom serial port

Sudo minicom-s

Note: The items selected below can also be in lowercase letters.

Select Serialport setup. The cursor is displayed on "Change which setting", type "A", move the cursor to the corresponding position of item A, and Change it to ttyUSB0 (because I am A USB-to-serial port ).

Configure the baud rate, data bit, and stop bit, and enter "E". The baud rate is 1152008N1 (Data bit 8, no parity check, stop bit 1 ), type "F" and "G" for hardware/software traffic control respectively, and select "No" (Note: If this parameter is not set to "NO", you cannot enter a character on the terminal ).

The specific configuration information is as follows:

Serial port setup [Enter]

+ ------------------------------------------------------------- +

| A-Serial Device:/dev/ttyUSB0 |

| B-LockfileLocation:/var/lock |

| C-CallinProgram: |

| D-CalloutProgram-: |

| E-Bps/Par/Bits: 115200 8N1 |

| F-Hardware FlowControl: No |

| G-Software FlowControl: No |

|

| Change whichsetting? |

+ ------------------------------------------------------------- +

Return to the upper-level menu and enter the Modemand dialing option:

A-Init string .........

B-Reset string ........

K-Hang-up string ......

Clear all three items

After confirming that the configuration is correct, you can press enter to return to the upper-level configuration interface and save it as the default configuration (that is, savesetup as dfl ). Finally, select the "Exit from Minicom" command to Exit.

5. Problems Encountered

Note: If the serial port is not used but is used directly, the SerialDevice must be configured as/dev/ttyS0.

1) if your/dev file does not contain ttyUSB0, enter

Mknod/dev/ttyUSB0 c 188 0

2) Restart minicom (note that the root permission is required). Otherwise, Device/dev/ttyUSB0 access failed: No such file or directory will be displayed.

$ Sudominicom

Make the configuration take effect. After connecting to the USB to serial port of the Development Board, you can print the correct serial port information in minicom. In the console, press Ctrl + a z to enter the minicom menu.

3) Device/dev/ttyS0 lock failed: the operation is not allowed. run ps-aux | grep minicom to check and kill the minicom process with kill-9, and then start the ps-aux | grep minicom terminal:

Warning: badsyntax, perhaps a bogu '-'? See/usr/share/doc/procps-3.2.7/FAQ

Root XXXX XXX

Root 8319 0.0 0.1 5416 676 pts/1 S + grep minicom

Then kill-9 XXXX. The XXXX here is similar to the 8319 on the second line. It is also a four-digit number.

4) if not, try to change the USB port and then perform the above steps again.

5) Run mincom on the terminal

6. Implement file transfer between PC and Development Board

Connect PC AND DEVELOPMENT BOARD

Start minicom, and then CTRL + A S

Select zmode and find the file to be sent, so that the cross-compiled executable file can be directly executed on the Development Board terminal!

Contact Us

The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion; products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the content of the page makes you feel confusing, please write us an email, we will handle the problem within 5 days after receiving your email.

If you find any instances of plagiarism from the community, please send an email to: info-contact@alibabacloud.com and provide relevant evidence. A staff member will contact you within 5 working days.

A Free Trial That Lets You Build Big!

Start building with 50+ products and up to 12 months usage for Elastic Compute Service

  • Sales Support

    1 on 1 presale consultation

  • After-Sales Support

    24/7 Technical Support 6 Free Tickets per Quarter Faster Response

  • Alibaba Cloud offers highly flexible support services tailored to meet your exact needs.