Chinese SSID wireless Network Setup method

The beauty of Chinese SSID wireless network settings

The SSID is the abbreviation for the Service Set identifier, which means that it is an identifier of the server. The SSID technology can divide a wireless LAN into several subnets that require different authentication, and each subnet requires independent authentication, only authenticated users can enter the corresponding subnet to prevent unauthorized users from entering the network.

SSID is a general concept, including Essid and BSSID, used to distinguish between different networks, can be up to 32 characters, the wireless card sets a different SSID can enter different networks, the SSID is usually broadcast by the AP, You can view the SSID in the current area with the scan feature that is available from XP. For security reasons, you can not broadcast the SSID, at which point the user must manually set the SSID to enter the appropriate network. Simply put, the SSID is the name of a local area network, and only computers set to values with the same SSID name can communicate with each other.

However, the SSID, which consists of letters and numbers, can be scanned into the corresponding wireless network and successfully invaded by tools such as BT3, BT4, and network ants, even if no "broadcast" is set. Only by modifying the SSID information to Chinese can the above problem be completely avoided. The reason, on the one hand, because Chinese characters in these software will display garbled, on the other hand, because many of the intrusion tools are developed by foreign developers, not supported by China, incompatible.

Some devices in the market fully support the Chinese SSID wireless network settings, but there are many devices do not support the use of Chinese to name the SSID, in this case, the two methods described in this article can be resolved.

Two ways to modify your choice

1. Browser method

Device requirements: The device requirements are relatively low, even if not for the wireless router brush dd-wrt or tomato and other Third-party firmware can also use this method to modify the SSID to Chinese.

The author's wireless router uses firmware that is dd-wrt and prompts the wireless network name (SSID) to contain the illegal Ascⅱ code when modifying the wireless network SSID message as a Chinese name and saving. This is because the wireless router management interface is written by JSP, and many JSP statements on the Chinese character support is not good, the purpose of using the browser method is to let no line by the management interface to support Chinese coding.

The first step: since many wireless router management interfaces are made from JSP or Java programs, you can disable the device's restrictions on the Chinese SSID Wireless network setting by prohibiting the loading of Java components. Because IE browser does not have the related function by default, only uses the Firefox browser to solve. First access to the wireless router management interface through the Firefox browser, the default will appear garbled.

The second step: in the Firefox browser "character encoding" in the language set to "Chinese" can solve the garbled problem. Also deselect the "Enable" option in the Firefox browser.

The third step: Refresh the Management page again, enter the Chinese SSID wireless network settings information and save, will no longer appear "illegal Ascⅱ code" prompts.

Fourth step: After saving, through the operating system's wireless scanning function, you can see the SSID modified as a Chinese character of the wireless network. When the settings are complete, uncheck the "Enable" option in the Firefox browser to avoid being affected when browsing other pages later.

2.Telnet method

The Telnet protocol is a member of the TCP/IP protocol family and is the standard protocol and main mode of Internet remote Landing service. It provides users with the ability to complete remote host work on the local computer. Use the Telnet program on the end user's computer to connect to the server. End users can enter commands in the Telnet program, which run on the server as if they were entered directly on the server's console. You can control the server locally. To start a Telnet session, you must enter a username and password to log on to the server. Telnet is a common way to remotely control a Web server.

Device Requirements: This method requires the wireless router to turn on the Telnet service, but not all wireless devices turn on the service by default, and you need to make sure that the service is turned on before proceeding.

Only the wireless router on which the Telnet service is turned on can be set up using this method.

The first step: Under normal circumstances, the dd-wrt or tomato and other third-party firmware of the wireless router will be enabled by default Telnet function, and some d-link, Linksys wireless router also has related functions. You only need to enter from the command Prompt window "Telnet

Wireless router management address "to detect, if there is a request to enter a username and password prompts, it indicates that the function has been turned on."

Tip: The username entered in the Telnet state is always root, and the password is consistent with the account password in the graphical admin interface.

Step two: Through telnet into the wireless router command line management interface, you can through the NVRAM set

Wl_ssid= the "Chinese SSID name" command to set a Chinese SSID, for example, the author enters the NVRAM set

Wl_ssid= "Lanzheng", the SSID broadcast network information is set to "Lanzheng".

The third step: After the modification, you can real-time through the graphical management interface to see the changes in SSID information, but will appear garbled, you can not ignore.

Step Fourth: Next, use the NVRAM commit command in the command line management interface to save the settings that were made, and then restart the reboot command.