Cisco 12 Series AP initialization configuration-Initialize configuration

For SSH login to this device

Bridge IRB

Bridge 1 Route IP turn on routing function

Interface BVI1

IP address 10.15.106.44 255.255.255.0 own addresses

!

IP default-gateway 10.15.106.1 Gateway

IP forward-protocol nd

IP HTTP Server

No IP http secure-server

IP http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag

IP Route 0.0.0.0 0.0.0.0 10.15.106.1

VLAN Configuration

dot11 Vlan-name Mgmt VLAN 330 330 is used to log on to this AP

dot11 vlan-name User VLAN 332 332 is provided to users to connect the

Open SSH

Crypto key gene RSA General-key mod 1024

IP SSH ver 2

Interface GigabitEthernet0

No IP address

Duplex Auto

Speed auto

!

Interface GigabitEthernet0.330//physical sub-interface number to be the same as the VLAN number behind the dot1q

Encapsulation dot1q Native//Let management VLAN330 provide services from this physical sub-interface

Bridge-group 1//Call Bridge Group to activate this port's routing function, in this step can ssh, of course, there is a premise is to set up a local account and enable password

Bridge-group 1 spanning-disabled

No Bridge-group 1 source-learning

!

To provide wireless services to users

SSID Configuration

Dot11 SSID Pchome-1

VLAN 332

Authentication Open

Authentication key-management WPA Version 2 encryption method

Guest-mode//This command is used to open, equivalent to the role of a switch! It's important!

WPA-PSK ASCII 7 045d0f1e1a78145a1b1a57 This place to play password, show is garbled, in fact, this 7 plus space behind your password

Wireless Radio Configuration

Radio 0 is 2.4GHz, Radio 1 is 5GHz, two configuration is the same, here is 0

Interface Dot11radio0

No IP address

IP helper-address 192.168.0.1

!

Encryption VLAN 332 mode ciphers AES-CCM TKIP//Here is a description of the 332 VLAN sent to the user

!

SSID Pchome-1 calls the SSID that was just created

!

Antenna gain 0

Stbc

Beamform OFDM

Station-role Root

Bridge-group 1

Bridge-group 1 Subscriber-loop-control

Bridge-group 1 Block-unknown-source

No Bridge-group 1 source-learning

No Bridge-group 1 unicast-flooding

!

Interface dot11radio0.332

Encapsulation dot1q 332//This is also the calling VLAN, and the VLAN numbers behind the sub-interfaces and dot1q must also be consistent

IP helper-address 192.168.0.1

Bridge-group 255

Bridge-group 255 Subscriber-loop-control

Bridge-group 255 spanning-disabled

Bridge-group 255 Block-unknown-source

No Bridge-group 255 source-learning

No Bridge-group 255 unicast-flooding

Don't forget to put dot11 0 and 1 No shut to open these two bands radio

A few of the frequently used show commands

Pchome-ap7#sho IP int BR

Interface ip-address OK? Method Status Protocol

BVI1 10.15.106.44 YES Manual up

Dot11radio0 Unassigned YES unset up

dot11radio0.332 Unassigned YES unset up

Dot11radio1 Unassigned YES unset up

dot11radio1.332 Unassigned YES unset up

GigabitEthernet0 Unassigned YES unset up

GigabitEthernet0.330 Unassigned YES unset up

GigabitEthernet0.332 Unassigned YES unset up

The show IP int br is used to look at the port up-down, if you see RADIO1 and its sub-interface is down the description of 5GHz is not in the hair

Pchome-ap7#sho dot11 Bssid

Interface BSSID Guest SSID

Dot11radio0 08cc.6867.5320 Yes pchome-1

Dot11radio1 08cc.6869.5160 Yes pchome-1

To see the status of the radio in two bands, guest shows Yes below the transmit signal

Pchome-ap7#show dot11 Associations Client

802.11 Client stations on DOT11RADIO1:

SSID [pchome-1]:

MAC address IP address Device Name Parent state

C0ee.fb01.3bb6 192.168.1.108 unknown-self Assoc

pchome-ap7#

Use to see which client is connected above, which radio

Configuration of the upstream switch

Interface GIGABITETHERNET1/0/48
Description Cn-sha1-10-ap1242ag-1
Switchport trunk Native VLAN//native VLAN write management VLAN for AP
Switchport mode Trunk
End

Cisco 12 Series AP initialization configuration-Initialize configuration