Cisco HSRP Dual-machine configuration

Cisco HSRP Configuration

• Network topology

650) this.width=650; "src=" http://s5.51cto.com/wyfs02/M00/80/77/wKiom1dClk6hrij9AAGYiQDg5i0740.jpg "title=" Network Topology " Style= "Float:none;" alt= "wkiom1dclk6hrij9aagyiqdg5i0740.jpg"/>

• Configuration commands

ha-a Configuration Commands

Ha-a>enable

Ha-a#conf Terminal

Enter configuration commands, one per line. End withcntl/z.

Ha-a (config) #int gigabitethernet 0/2

Ha-a (config-if) #no switchport [Zhou Shuxuan 1]

Ha-a (config-if) #ip address 192.168.30.2 255.255.255.0[Zhou Shuxuan 2]

Ha-a (config-if) #exit

Ha-a (config) #int gigabitethernet 0/1

Ha-a (config-if) #no Switchport

Ha-a (config-if) #ip address 10.10.10.10 255.255.255.0

Ha-a (config-if) #exit

Ha-a (config) #ip routing[Zhou Shuxuan 3]

Ha-a (config) #router rip[Zhou Shuxuan 4]

Ha-a (config-router) #ver 2

Ha-a (config-router) #no auto-summary[Zhou Shuxuan 5]

Ha-a (config-router) #network 10.10.10.0[Zhou Shuxuan 6]

Ha-a (config-router) #network 192.168.30.0

Ha-a (Config-router) #exit

Ha-a (config) #interface gigabitethernet 0/2

Ha-a (config-if) #standby 1 IP 192.168.30.254[Zhou Shuxuan 7]

Ha-a (config-if) #standby priority[Zhou Shuxuan 8]

Ha-a (config-if) #standby 1 preempt[Zhou Shuxuan 9]

Ha-a (config-if) #standby 1 Timers 3[Zhou Shuxuan]

Ha-a (config-if) #standby 1 track gigabitethernet 0/2[Zhou Shuxuan]

Ha-b Switch Configuration

Ha-b>enable

Ha-b#conf Terminal

Enter configuration commands, one per line. End with cntl/z.

Ha-b (config) #int gigabitethernet 0/2

Ha-b (config-if) #no Switchport

Ha-b (config-if) #

Ha-b (config-if) #ip address 192.168.30.2 255.255.255.0

Ha-b (config-if) #exit

Ha-b (config) #int gigabitethernet 0/1

Ha-b (config-if) #no Switchport

Ha-b (config-if) #ip address 10.10.10.10 255.255.255.0

Ha-b (config-if) #exit

Ha-b (config) #ip routing

Ha-b (config) #router rip

Ha-b (config-router) #ver 2

Ha-b (config-router) #no auto-summary

Ha-b (config-router) #network 10.10.10.0

Ha-b (config-router) #network 192.168.30.0

Ha-b (Config-router) #exit

Ha-b (config) #interface gigabitethernet 0/2

Ha-b (config-if) #standby 1 IP 192.168.30.254

Ha-b (config-if) #standby 1 preempt

Ha-b (config-if) #standby 1 Timers 3 10

Ha-b (config-if) #standby 1 track gigabitethernet 0/2

third, querying the HSRP state

Query command: Show standby brief

650) this.width=650; "src=" Http://s5.51cto.com/wyfs02/M00/80/75/wKioL1dClz_BvNqzAAAX7Mj8524458.png "title=" View VRRP status "style=" Float:none; "alt=" Wkiol1dclz_bvnqzaaax7mj8524458.png "/>

Ports on: GIG0/2 GRP Group Id:1 active: Active routed locally

Standby: Backup route on 192.168.30.2

Virtual IP Gateway ip:192.168.30.254

Query command: Show standby

650) this.width=650; "src=" Http://s5.51cto.com/wyfs02/M01/80/77/wKiom1dClk6hm0fGAAA4nxwmlFs927.png "title=" View VRRP Information "style=" Float:none; "alt=" Wkiom1dclk6hm0fgaaa4nxwmlfs927.png "/>

[Zhou Shuxuan 1] switching mode for closed ports Enable routing mode

[Zhou Shuxuan 2] of the configuration port IP Address

[Zhou Shuxuan 3] to start the routing capability for layer three switches

[Zhou Shuxuan 4] Configuration RIP Dynamic Routing

[Zhou Shuxuan 5] Close RIP V2 Auto-summarize function

[Zhou Shuxuan 6] Configuring dynamic routing for Advertisement

[Zhou Shuxuan 7] enabled HSRP features, creating Standby Group 1 , and set up a virtual gateway IP Address

[Zhou Shuxuan 8] Set HSRP priority, the value of which is larger will preempt the Active router, default is -

[Zhou Shuxuan 9] setting allows preemption to be active when the router priority is highest

[Zhou Shuxuan] Set Hellotime to be 3 seconds, Holdtime to be Ten seconds, which is the default value

[Zhou Shuxuan] Configure Port Tracking

This article is from the "Ink Color Dust" blog, please make sure to keep this source http://qianer520.blog.51cto.com/10583764/1782095

Cisco HSRP Dual-machine configuration