Cisco wireless AP Brush for FAT AP

First, this is ready to upgrade the equipment model AIR-CAP16021-C-K9

Second, set the IP address of the computer and ready TFTP: Set the computer IP to 10.0.0.2/8,tftp server is using SolarWinds 10.9.1.33.

Third, connect the console line to view the port of the console line

Four, use set serial port parameters as follows

Download 1602I of the FAT ap iOS file, url: http://down.51cto.com/data/1897579

My AP uses iOS is downloaded in 51CTO, other models of AP please download the corresponding iOS file

Six, modify the image file suffix is default, and placed in the TFTP root directory (key steps)

The name of the image file must be this: Ap1g2-k9w7-tar.default, if not the file name, will be an error as follows:

%error opening tftp://255.255.255.255/ap1g2-k9w7-tar.default (no such file or directory) APS:

The IP address must be set on this segment of 10.0.0.0/8 because the IP address used by the default AP upgrade is 10.0.0.1

Seven, in the case of power down the reset key, plug in power, press and hold reset for about 20 seconds, after the following prompt, you can release, then, the AP will automatically upgrade

IOS bootloader-starting System.

FLASH Chip:micron n25q256

Xmodem file system is available.

Flashfs[0]: Files, 9 directories

Flashfs[0]: 0 Orphaned files, 0 orphaned directories

FLASHFS[0]: Total bytes:31936000

Flashfs[0]: Bytes used:16559616

Flashfs[0]: Bytes available:15376384

Flashfs[0]: Flashfs fsck took seconds.

Reading Cookie from Seeprom

Base Ethernet MAC Address:18:e7:28:1a:2a:c7

Loopback_mode = 0

button is pressed, and wait for button to be released ...

Button pressed for seconds

Process_config_recovery:set IP address and config to default 10.0.0.1

Process_config_recovery:image Recovery

Image_recovery:download default IOS tar image Tftp://255.255.255.255/ap1g2-k9w7-tar.default

Examining Image ...

Extracting info (288 bytes)

Image Info:

Version Suffix:k9w7-.153-3.jab

Image Name:ap1g2-k9w7-mx.153-3.jab

Version Directory:ap1g2-k9w7-mx.153-3.jab

Ios Image size:1290752

Total Image size:11387392

Image feature:wireless lan| LWAPP

Image family:ap1g2

Wireless Switch Management version:8.0.72.236

Eight, after about five minutes of the brush process, you can enter the system

*mar 1 00:00:38.027:%sys-5-restart:system restarted--

Cisco IOS Software, C1600 Software (ap1g2-k9w7-m), Version 15.3 (3) JAB, RELEASE Software (FC1)

Technical Support:http://www.cisco.com/techsupport

Copyright (c) 1986-2014 by Cisco Systems, Inc.

Compiled Tue 02-sep-14 20:36 by Prod_rel_team

*mar 1 00:00:38.027:%SNMP-5-COLDSTART:SNMP agent on host AP is undergoing a cold start

*mar 1 00:00:38.955:%lineproto-5-updown:line protocol on Interface BVI1, changed

*mar 1 00:00:38.959:%lineproto-5-updown:line protocol on Interface Dot11radio0, changed

*mar 1 00:00:38.959:%lineproto-5-updown:line protocol on Interface Dot11radio1, changed

Ap>

Ix. Entry System

Ap> en

Enter the password Cisco

Ten, the next can be configured, we can configure the management address of the AP under the CLI, and then turn on HTTP management.

XI. configuration process (slightly)

12. Backup configuration file copy flash:/config.txt tftp://192.168.58.158 Backup is complete and duly completed.

Cisco wireless AP Brush for FAT AP