Cisco MDS9148 configuration procedure

Cisco MDS9148 configuration step 1. initialize the configuration of the Cisco9148 SAN Switch before logging on to the graphical interface. Www.2cto.com is connected by a random serial port debugging cable. The configuration is as follows. Enter the password for "admin": Confirm the password for "admin": ---- Basic System Configuration Dialog ---- This setup utility will guide you through the basic configuration of the system. setup configures only enough connectivity for management of the system. please register Cisco MDS 9000 Family devices promptly with your supplier. failure to register may affect response times for initial serv Ice CILS. MDS devices must be registered to receive entitled support services. press Enter at anytime to skip a dialog. use ctrl-c at anytime to skip the remaining dialogs. wocould you like to enter the basic configuration dialog (yes/no): y Create another login account (yes/no) [n]: <Enter> Configure read-only SNMP community string (yes/no) [n]: <Enter> Configure read-write SNMP community string (Yes/no) [n]: <Enter> Enter the switch name: localhost Continue with Out-of-band (mgmt0) management configuration? (Yes/no) [y]: <Enter> Mgmt0 IPv4 address: 10.77.77.77 Mgmt0 IPv4 netmask: 255.255.255.0 Configure the default gateway? (Yes/no) [y]: n Configure advanced IP options? (Yes/no) [n]: <Enter> Enable the ssh service? (Yes/no) [y]: n Enable the telnet service? (Yes/no) [n]: y Enable the http-server? (Yes/no) [y]: <Enter> Configure clock? (Yes/no) [n]: <Enter> Configure timezone? (Yes/no) [n]: <Enter> Configure summertime? (Yes/no) [n]: <Enter> Configure the ntp server? (Yes/no) [n]: <Enter> Configure default switchport interface state (shut/noshut) [shut]: <Enter> Configure default switchport trunk mode (on/off/auto) [on]: auto Configure default switchport port mode F (yes/no) [n]: <Enter> Configure default zone policy (permit/deny) [deny]: <Enter> Enable full zoneset distribution? (Yes/no) [n]: <Enter> Configure default zone mode (basic/enhanced) [basic]: <Enter> The following configuration will be applied: password strength-check switchname localhost interface mgmt0 ip address 10.77.77.77 255.255.255.0 no shutdown no feature ssh feature telnet feature http-server system default switchport shutdown system default switchport trunk mode auto no system default zone default-zon E permit no system default zone distribute full no system default zone mode enhanced www.2cto.com wocould you like to edit the configuration? (Yes/no) [n]: <Enter> Use this configuration and save it? (Yes/no) [y]: <Enter> [#################################### ####] 100% here, device Initialization is complete. 2. Open IE and enter the configured IP address in the address bar ( http://10.77.77.77 ), Open the following interface. 3. Click "Cisco Device Manager" to open the following interface. 4. Click "Continue" to open the following interface. 5. Click "Next" to install the software. Click "Next", click "Install", and click "yes" to start software installation. 6. After the software is installed, open the following interface and enter the set password "123ibm!" in the password bar! @ # IBM ". 7. Click "Open" to Open the control interface. 8. Click "FC-> Quick Config" to open the configuration page. 9. Set the zone on the open control interface. Click "Next" to check whether the zone settings are correct. Click "Finish" to complete the zone configuration. 10. Run the following command in the command line to check whether the zone is activated. Admin # show zone active zone name z_fc00005_fc00000000v1 vsan 1 * fcid 0xb80500 [interface fc1/5 swwn 20: 00: 00: 05: 73: da: b1: 50] * fcid 0xb80000 [interface fc1/1 swwn 20: 00: 00: 05: 73: da: b1: 50] zone name z_fcda-5_fc1_2_v1 vsan 1 * fcid 0xb80500 [interface fc1/5 swwn 20: 00: 00: 05: 73: da: b1: 50] * fcid 0xb80200 [interface fc1/2 swwn 20: 00: 00: 05: 73: da: b1: 50] zone name Z_FC1_6_FC1_3_V1 vsan 1 * fcid 0xb80400 [inter Face fc1/6 swwn 20: 00: 00: 05: 73: da: b1: 50] * fcid 0xb80100 [interface fc1/3 swwn 20: 00: 00: 05: 73: da: b1: 50] zone name z_fc00006_fc00004_v1 vsan 1 * fcid 0xb80400 [interface fc1/6 swwn 20: 00: 00: 05: 73: da: b1: 50] * fcid 0xb80300 [interface fc1/4 swwn 20: 00: 00: 05: 73: da: b1: 50] zone name $ default_zone $ vsan 1 www.2cto.com 11. Run the following command to check whether zoneset has been saved successfully. Admin # show zoneset name ZONESET_V1 vsan 1 zone name z_fc00005_fc00000000v1 vsan 1 interface fc1/5 swwn 20: 00: 00: 05: 73: da: b1: 50 interface fc1/1 swwn 20: 00: 00: 05: 73: da: b1: 50 zone name Z_FC1_5_FC1_2_V1 vsan 1 interface fc1/5 swwn 20: 00: 00: 05: 73: da: b1: 50 interface fc1/2 swwn 20: 00: 00: 05: 73: da: b1: 50 zone name Z_FC1_6_FC1_3_V1 vsan 1 interface fc1/6 swwn 20: 00: 00: 05: 73: da: b1: 50 interface fc1/3 swwn 2 0: 00: 00: 05: 73: da: b1: 50 zone name z_fc00006_fc00004_v1 vsan 1 interface fc1/6 swwn 20: 00: 00: 05: 73: da: b1: 50 interface fc1/4 swwn 20: 00: 00: 05: 73: da: b1: 50 12. The WWN numbers in the two switches.