After we have configured the basic Secure password protection for the router, there are some basic information about the router that need to be configured, such as the router banner information and description information that the user can see in the landing router.
1 If we want all the administrators of the company to see a warning message on the landing router: the command process is as follows
Yong1>enable
Yong1#conf T
Yong1 (config)#banner moth #Warning!! Don ' t change any configuration #
Yong1 (config) #exit
Yong1#exit
The next time you log in to the router into user mode (>) you will see the warning message we set above.
650) this.width=650; "title=" capture.jpg "src=" http://s5.51cto.com/wyfs02/M01/7C/E2/wKioL1ba9UfxAcj7AABM529Z_ Xa897.jpg "width=" 336 "height=" 339 "alt=" Wkiol1ba9ufxacj7aabm529z_xa897.jpg "/>
2 We can also configure a description for each port to indicate the purpose of the port or the next hop (i.e. where the connection is going).
Yong1 (config) # ' command omitted before entering configuration mode
Yong1 (config) #interface gigabitethernet 0/0 ' Enter gigabitethernet 0/0 Port configuration Mode
Yong1 (config-if) #description This port connect to BT
Yong1 (config-if) #exit
Yong1 (config) #exit
yong1#show interface gigabitethernet 0/0 ' Show gigabitethernet 0/0 Port Information
650) this.width=650; "title=" 2.JPG "src=" Http://s1.51cto.com/wyfs02/M02/7C/E3/wKiom1ba9Ouix4Z9AAD-ubbPrIc944.jpg " alt= "Wkiom1ba9ouix4z9aad-ubbpric944.jpg"/>
3 Configure local time for routers
Yong1#clock set 11:00:00 2016
Yong1#show Clock
650) this.width=650; "title=" 3.JPG "src=" Http://s2.51cto.com/wyfs02/M02/7C/E2/wKioL1ba9XzCzqsPAAA_jc6NrIw608.jpg " alt= "Wkiol1ba9xzczqspaaa_jc6nriw608.jpg"/>
4 By default, the router will parse the error command as a name that needs to be resolved when we strike the wrong command, and this process takes time. So we need to turn the command parsing off .
Let's take a look at the status before closing: This process takes a few 10 seconds to wait.
650) this.width=650; "title=" 4.JPG "src=" Http://s3.51cto.com/wyfs02/M00/7C/E3/wKiom1ba9TCBJOeVAAA0C44llAA015.jpg " alt= "Wkiom1ba9tcbjoevaaa0c44llaa015.jpg"/>
Yong1 (config) #no IP domain-lookup
After the execution of the order, we will not delay the time when we have the wrong command.
650) this.width=650; "title=" 5.JPG "src=" Http://s5.51cto.com/wyfs02/M00/7C/E2/wKioL1ba9dWyxrW1AAA33f06Fl4523.jpg " alt= "Wkiol1ba9dwyxrw1aaa33f06fl4523.jpg"/>
This article is from the "Guo Yong Technology blog" blog, make sure to keep this source http://guoyong.blog.51cto.com/408495/1747955
Cisco router basic Information Configuration---Set time, warning information, and port information