Omniswitch the command to view the log is: Format: Show log swlog [timestamp start_time [end_time]]show log swlog timestamp 05/21/2015 11:30 05/21/201 5 12:30 Discover that adding a router privately causes DHCP distribution to confirm the router IP, find the MAC, switch to the MAC corresponding port, close this port to search for this router location, master its Administrator account and password, turn off the DHCP function. Show configuration Snapshotshow VLAN rules add managed switch, MAC address bound 0 segment, ARP bind AAA authentication default local #开启所有服务, Default is off need console go in Set AAA authentication HTTP local #开启http服务, default is off need console go in Set AAA authentication Telnet local #开启telnet服务, Default is off need console go in Set AAA authentication FTP local #开启ftp服务, default is off need console go in Set IP interface "VLAN 1" address 10.6.0.143 Mask 255 .255.255.0 VLAN 1 ifindex 1 VLAN Port mobile 2/38 BPDU ignore enable MAC address binding ARP 10.6.0.136 00:e0:b1:d8:16:19 VLAN no port Mobile 1/21vlan Port default 1/21mac-address-table permanent 00:1b:82:ff:03:e5 1/21 100no mac-address-table permanent 00:1b:82:ff:03:e5 1/21
Policy condition C1 Source VLAN Destination IP 10.6.0.0 Mask 255.255.0.0policy condition C2 Source VLAN 101 Destinati On IP 10.6.0.100policy condition C3 source VLAN 1010 Destination IP 10.6.0.0 Mask 255.255.0.0policy condition C4 Source VL An destination IP 10.6.100.0 mask 255.255.255.0policy condition c5 Source vlan 1020 Destination IP 10.6.0.0 Mask 255.25 5.0.0policy condition C6 Source VLAN Destination IP 10.6.100.0 Mask 255.255.255.0policy action A1 Disposition Droppolic Y action A2 Maximum bandwidth 128Kpolicy action A3 Disposition denypolicy action Flowshape maximum bandwidth 128Kpolicy ru Le R1 condition C1 action A1policy rule R2 condition C3 action A1policy rule R3 Condition C4 action a3policy rule R4 Condi tion C2 action a3policy rule R5 condition C5 action a1policy rule R6 condition C6 Action A3qos Apply
Policy condition Source1 Source IP 10.6.1.253 Mask 255.255.255.255policy condition dest1 Destination IP 10.6.1.253 Mask 25 5.255.255.255policy Action No Disposition denypolicy Action Yes disposition acceptpolicy rule permitrule Precedence Co Ndition source1 Action Yes reflexivepolicy rule denyrule condition dest1 action Noqos apply
Only allow PC access to specified Pcqos enablepolicy condition iptest Source IP 10.6.4.226policy condition iptest2 source IP 10.6.4.226 destinatio n IP 10.6.4.51 Mask 255.255.255.255policy action NO disposition denypolicy Action YES disposition acceptpolicy rule R1 pre Cedence condition iptest Action no-> policy rule R2 precedence $ condition iptest2 Action yes-> QoS apply  ;-> no policy rule r1-> no policy rule r2-> no policy condition iptest-> no policy condition Iptest2 poli Cy condition host42 Source IP 10.6.100.42-> no policy condition host42-> policy condition host42 Source IP 10.6.100. Destination IP 10.6.100.0 Mask 255.255.254.0-> policy rule tmpno42 Precedence $ condition host42 action a1-> Qo s applypolicy condition host10 source IP 10.6.100.42 Destination IP 10.6.1.0 mask 255.255.255.0-> policy rule No10 Prec Edence Condition host10 Action a1-> QoS apply -> No policy rule no10-> no policy rule tmpno42QoS Apply
Policy condition ip1010 Source IP 192.168.11.0 mask 255.255.255.0 destination IP 10.6.0.98 Mask 255.255.255.255
Policy Action A4 Disposition Accept
Policy rule R2 condition ip1010 action A4
Policy condition C3 Source VLAN 1010 Destination IP 10.6.0.0 Mask 255.255.0.0
Policy Rule R11 Condition C3 action A1
No policy rule R2
No policy rule R11
No policy action A4
No policy action Yesqos apply
DHCP delay finally resolves IP helper forward delay 0 view the MAC address of a direct-attached device arp-a snmp -> user public password public Read-write all no auth -> SNMP station 10.6.0.71 162 "public" V1 enable snmpwalk-c public-v 2c 10.6.0.133&N BSP;  SNMP Community Map "public" user "admin" on snmp Community Map Mode OFF SNMP Security No Securit Y AAA Authentication snmp "local"  SNMP station 10.6.0.71 162 "public" V1 enable snmp authentication trap EN Able user password-size min 5 snmp trap absorption enable snmp trap to WebView Enable ip Helper no address 10.6.0.84 VLAN 40 IP Helper no address 10.6.0.84 VLAN 1020 IP Helper no address 10.6.0.73 VLAN 10 IP Helper No address 10.6.0.73 VLAN 20 IP Helper no address 10.6.0.73 VLAN 30 IP Helper No address 10.6 .0.73 VLAN 101 IP Helper no address 10.6.0.73 VLAN 1000 IP Helper no address 10.6.0.73 VLAN 1010 IP Helper No address 10.6.0.73 VLAN 1020&NBSP: Set time zone, time, time, date, hostname, tender, etc. ***************************************************system timezone Pstsystem timezone ZP8 (China) System daylight Savings Time Enablesystem time 18:35:00system date 06/27/2002system Contact "JSmith X477 [EMAIL&NB Sp;protected] "system name" Engineering Switch 3 "system location" NMS lab--ne Corner Rack "****************************** Restart: ***********************************************************reload working No Rollback-timeout (restart now) reload Primary in 3:03 (timed reboot main module) reload primary at 20:00 June 30 (timed reboot main module) Reload primary Canc El (Cancel reboot Master module) reload secondary (restart Standby management module) reload cancel (cancel reboot) *************************************************** Save configuration: ************************************************************copy Running-config working or Write memory (save to main module RAM) copy working certified (save to standby config file) copy certified working (Restore profile) copy Flash-synchro (Synchronizing configuration files to the Standby management module) ************************************************************* vlan withReset: ************************************************************* vlan Port mobile 2/38 BPDU Ignore Enablevlan 10 Create VLAN 10vlan name Bangonglou gives VLAN 10 name VLAN router IP 172.16.32.1 mask 255.255.255.0 to VLAN with router Ipvlan prot D Efault 1/1 1/1 ports assigned to VLAN 10 vlan port default 2/32vlan 2 802.1q 8/1 8/1 ports on VLAN 2 802.1q tagvlan 2 no port default 3/1-5 remove 3/1-5 IP from VLAN 2 interface "vlan-1" address 192.168.0.254 mask 255.255.255.0 VLAN 1 Configure route vlan1 for ip************** Common Maintenance Command: ************************************************** Show micrcode view software information show running-directory view switch run mode show configuration snapshot all view all configurations show history Parameters View History Parameters Show Historical View historic Information show VLAN view VLAN information show Chassis view switch chassis information macshow Module View modules Information show Ni view ni info show cmm View Management module Information Show System view systems information show Seesion configshow dnsshow NTP server statusshow NTP client server-listshow NTP c Lientshow reloadshow Reload Statusshow userShow hardware info*********************************************************** file Operation command: **********************  RM *.imginstall *.img cdpwdlscpmkdirrmvimovechmoddeletefreespacefscknewfs************************************************************  ACL configuration: **************************************************************** only allow 192.168.10.0/24 network segments to access any, While 192.168.10.0/24 does not allow any network access:-> policy condition source1 Source IP 192.168.10.0 Mask 255.255.255.0-> policy condition D Est1 Destination IP 192.168.10.0 mask 255.255.255.0-> policy Action No disposition deny-> policy action Yes disposit Ion accept-> policy rule permitrule precedence condition Source1 action Yes reflexive-> policy Rule denyrule con Dition dest1 Action no-> QoS apply****************************************************************** Avlan Configuring:**************************************************************** system name os6600 VLAN 1 Router IP 192.168.1.1 VLAN 2 router IP 192.168.2.1 VLAN 2 enable VLAN 2 authentication en able VLAN Port mobile 8/3 VLAN Port 8/3 authentication enable AAA radius- Server "Rad1" host 192.168.1.254 key switch Auth-port 1812 Acct-port 1813 AAA authentication VLAN Single-mode "Rad1" AAA accounting VLAN rad1 IP HELPR address 192.168.1.254 AAA Avlan default DHCP 192.168.1.1 IP Helper Avlan only avlan auth-ip 3 10.10.2.80 no AAA radius-serve R rad1 AAA VLAN no no AAA Authentication vlan no AAA accounting**********************  SLB Configuration: *******************************************************ip SLB Admin enableip slb cluster ZBSLB VIP 192.168.0.234ip SLB server IP 192.168.0.236 cluster zbslbip SLB server IP 192.168.0.2 PNS cluster ZBSLBIP SLB probe ZBSLB_PROBE1 PINGIP SLB cluster ZBSLB probe zbslb_probe1ip SLB server IP 192.168.0.236 cluster ZBSLB probe ZBSLB_PROBE1IP SLB server I P 192.168.0.237 cluster ZBSLB probe zbslb_probe1********************************************************** DHCP relay configuration **********************************************************ip UDP Relayip helper Address 192.168.1.1ip Helper No address 192.168.1.1 (deletes one address) IP Helper No address (delete all address) IP Helper address 192.168.3.1 VLAN 3IP Helper address 192.168.4.1 192.168.4.2 VLAN 4IP Helper forward delay (set forward delay timer for the BOOTIP/D HCP relay) 1-65535ip Helper Maximum Hops 3 (set the maximum hop count value) 1-16show IP helperip helper boot-up enable DHCP IP Helper boot-up enable bootpshow IP helper statsshow IP UDP relay serviceshow IP UDP relay statisticsshow IP UDP relay D Estination**********************************************************
Interfaces 1/1 Duplex?
^
Half full AUTO
(Interface Command Set)
-Interfaces 1/23 Speed 100
-Interfaces 1/23 speed auto-> interfaces 1/23 Speed 100
From for notes (Wiz)
Common commands for Alcatel switches
