Configuration Methods for common models of adsl Modem

Note: If you need to set up another type of server, the listening protocol and port are different when "port ing" is set. For details about the port and its description, see:
The following table lists some common network services and their corresponding port numbers.
Service name port number/Protocol [alias] # comment
The ftp-data20/tcp # FTP, data
Ftp 21/tcp # FTP. control
Telnet 23/tcp
Smtp25/tcp mail # Simple Mail Transfer Protocol
Time37/tcp timserver
Time37/udp timserver
Domain 53/tcp # Domain Name Server
Domain 53/udp # Domain Name Server
Tftp69/udp # Trivial File Transfer
Gopher 70/tcp
Http80/tcp www-http # World Wide Web
Pop3110/tcp # Post Office Protocol-Version 3
Nntp119/tcp usenet # Network News Transfer Protocol
Netbios-ns 137/tcp nbname # NETBIOS Name Service
Netbios-ns 137/udp nbname # NETBIOS Name Service
Netbios-dgm 138/udp nbdatasync # NETBIOS datemediservice
Netbios-ssn139/tcp nbsession # NETBIOS Session Service
Imap143/tcp imap4 # Internet Message Access Protocol
Snmp161/udp # SNMP
Snmptrap162/udp snmp-trap # SNMP trap
Irc 194/tcp # Internet Relay Chat Protocol
Ipx 213/udp # IPX over IP
Ldap389/tcp # Lightweight Directory Access Protocol
Https 443/tcp MCom
Https 443/udp MCom
Uucp540/tcp uucpd
Ldaps 636/tcp sldap # LDAP over TLS/SSL
Doom666/tcp # Doom Id Software
Doom666/udp # Doom Id Software
Phone 1167/udp # Conference calling
Ms-sql-s1433/tcp # Microsoft-SQL-Server
The ms-sql-s1433/udp # Microsoft-SQL-Server
Ms-sql-m1434/tcp # Microsoft-SQL-Monitor
The ms-sql-m1434/udp # Microsoft-SQL-Monitor
Wins1512/tcp # Microsoft Windows Internet Name Service
Wins1512/udp # Microsoft Windows Internet Name Service
L2tp1701/udp # Layer Two Tunneling Protocol
Pptp1723/tcp # Point-to-point tunnelling protocol
Radius 1812/udp # RADIUS authentication protocol
Radacct 1813/udp # RADIUS accounting protocol
Nfsd2049/udp nfs # NFS server
Knetd 2053/tcp # Kerberos de-multiplexor
Man 9535/tcp # Remote Man Server
Set port ing in ASUS 6000EV/6005HW adsl modem:
Click "NAT" in the main menu and there will be a "nat channel list". In this example, the web server is set up on the internal pc 192.168.1.2. The default web port is 80. The settings are as follows: enter the following content in mupltiple port forwarding in the nat channel list:
Action: add
Channel n1
Protocol: tcp
Incoming port, begin: 80, end: 80
New port begin: 80, end: 80
New ip address: 192.168.1.2.
See http://www.asus.com.cn/products/com...on/download.asp for Detailed Help
Set port ing in linksys adsl Router:
In the main menu, click "advanced". In the next menu, there is a "forwarding". In this example, the web server is set up on the internal pc 192.168.1.2. The default web port is 80. The settings are as follows:
Extport: 80 to 80
Ip address: 192.168.1.2
Click "apply ".
Set port ing in the broadband blue elf router:
On the Advanced Settings page, click "Distributed Servers Setup (Virtual Serves, Virtual host settings )"
Each Virtual Server is defined as a Service Port. All accesses to this Port are redirected to the computer corresponding to the corresponding Service IP address.
For example, if you want:
Set up an FTP server on 192.168.123.10. (Port 21)
Set up an Email smtp server on 192.168.123.20. (Port 25)
Set up a Web server on 192.168.123.30. (Port 80)
Set up a Pop server on 192.168.123.40. (Port 1, 110)
You need to make the following settings on this page:
Service Port Service IP Enable
FTP 21 192.168.123.10 √
Email 25 192.168.123.20 √
Web 80 192.168.123.30 √
Post Office 110 192.168.123.40 √
Jinbao kinpo) Port ing on A400
The router port is forwarded in "packetfilter.
In the example of setting up a web server, the Lan address of the router is 192.168.1.1, And the ip address of the web server is 192.168.1.2, which must be in the same network segment as the ip address of the Lan of the router ). Specifically:
Enable package filtering: Tick.
Source Address: Any ip address, check
Port: 80
Target address: the ip address of your intranet machine is 192.168.1.2,
Target Port: 80.
Priority: Any number
Protocol: tcp
Action: allow.
Click Add.
Configure port ing on Bell 6309:
This router is configured in lineconfiguration.
In the example of setting up a web server, the Lan address of the router is 192.168.1.1, And the ip address of the web server is 192.168.1.2, which must be in the same network segment as the ip address of the Lan of the router ). Specifically:
In "inbound" of "Nat" in "lineconfiguration"
Port: 80
Host: 192.168.1.2,
Protocol: tcp
Then "add. Add port 21 for ftp, and set port 25,110 for the email server.
Successful port ing for omnidirectional 1680ADSL:
My Internet cafe format: omnidirectional adsl with route) + hub
No server,
My goal is to set one machine to 192. 168. 1. 14) provide web and ftp services to the Internet.
Method: Enter the configuration item of the omnidirectional adsl, enter the advanced configuration item, select the virtual server, and there will be three blank items, if you only want to be in 192. 168. 1. 14 assume that the web and ftp can be entered as follows:
8080192. 168. 1. 14. Click add.
2121192. 168. 1. 14. Click add.
Then save the settings and enable the logger to restart the dial.
Software Installation: After the ing, the value is 192. 168. 1. 14. Install the dynamic dns software and then install the web and ftp software. After my experiment, it is completely normal.
Chinamoocs ADSL automatic dial-up multi-host internet sharing settings
1. Set the IP address of a computer that requires Internet access to 192.168.1.2 as long as it is not 192.168.1.1.) The subnet mask is 255.255.255.0. If the machine is WIN9X, the system will prompt you to restart the machine.
2. After step 1 is completed, open IE, enter 192.168.1.1 in the address bar, and press Enter.
Enter root at the user name.
Enter 12345 as the default logon username and password .)
Click OK to go to The zhongda settings window.
3. Click settings in basic settings.
Delete all options in the current list of all ATM PVCs. Be sure to delete all options !!!!
4. Click the PPPoE activation NAT option on the right,
Make the following settings: ******** indicates the phone number used for broadband Internet access)
VPI: 0VCI: 35
User name: pja ******* password :*******
Mode: AUTO idle: 30000
Authentication: PAP activates the DHCPSERVER and adds "quit" to it"
At last, click ADD. However, another step is more critical, ^ O ^)
5. Click SAVE and restart in basic settings on the left, click SAVE first, SAVE and restart in basic settings on the left, and Click Reboot. Disable IE and surf the Internet in 40 seconds.
6. Additional instructions:
A. According to the above settings, chinamoocs will automatically start the DHCP service, so that no IP address is required for each computer. However, its default service IP address ranges from 192.168.1.3 to 192.168.1.131. To increase the number of machines, follow these steps. Click DHCP in advanced settings. First, disable the DHCP service. Click Disable on the right. Enter 192.168.1.255 at the maximum IP address. Make sure to activate the DHCP service again.
B. You can choose to automatically obtain an IP address for each computer without an IP address ). However, DNS and gateway are required.
Set DNS to 202.96.64.68 and 202.96.75.68.
Set the gateway to 192.168.1.1.
C. All Internet computers and CEN are directly connected to the hub or vswitch ).
Settings of the built-in automatic dial-up sharing Function of ittech ADSL:
Enable the TD-2001ADSL built-in PPPOE dial to achieve multi-machine access to the premise!
The use of TD-2001 for PPPOE built-in implementation of sharing must be validated:
The Firmware version of TD-2001 adsl modem should be V3.x or above;
The Internet access method is PPPOE virtual dialing;
The preceding conditions are indispensable.
Confirm the FIRMWARE Version and enter the Version through "telnet 192.168.1.1 ".
Firmware version: The TD2000917-26TWA3.x is V3.x, which can be upgraded if not;
For virtual dialing, you must confirm the account and password. In addition, you must record the previous VCI and VPI values before the upgrade.
Now the ETEK TD-2001 ADSL 3.04 and later versions of the bridge mode has built-in PPPOE automatic dialing function.
The procedure for building the PPPOE automatic dialing function in bridging mode is as follows:
Note: This function is only intended for virtual dial-up users and is unavailable in other modes. Users in other modes are not allowed to modify this function.
Step 1: connect the MODEM and the workstation network cable to the hub and confirm that the connection is normal.
The operation on the WEB interface is to install the modem on the desktop, disconnect the power of the modem, and then connect it to IE. In the address column, enter 192.168.1.1, enter the password as required: 12345. The Web UI is displayed)
1) Open the Web UI, click "atm pvc" on the left, and then click "PPPoe…" under "Connection List" on the right border ......", Click "Delete" to Delete all the PVC values under the original bridge. Click "OK" below ".
2) enable the DHCP server and DNS relay enable. Click "OK" below ".
Note: If you want the PC to automatically obtain the IP address, you can enable the DHCP server enable function), if you want to specify the IP address of the pc dhcp server disable ), remember that the IP address of the PC must be in the same network segment as the lan ip address of the adsl modem, And the gateway and DNS point to the lan ip address. If you encounter instability, you can try DNS relay disable and enter the real DNS202.96.64.68 provided by China Telecom in the DNS of the PC Nic .)
3) on the Web UI, click Save Configuration on the left, save on the right, and Reboot on the left ", click "Reboot" on the right to restart the MODEM. To be secure, it is best to restart your computer.
The above steps must be stored !)
Step 2: run the following commands on the CONSOLE to start the Super Terminal: Enter "telnet 192.168.1.1" in "start"-"run", and enter the password 12345, enter the following command)
192.168.1.1> ip device add ppp_device ether // ppp/DEVICE = 1
192.168.1.1> ip nat add ppp_device
192.168.1.1> ppp 1 clear
192.168.1.1> ppp 1 welogin [account] [Password] chap
Note: enter your account in the [account] field, enter your password in the [Password] field, and there is a space between the password and the account)
192.168.1.1> ppp 1 pppoe atm 0 35
192.168.1.1> ppp 1 enable
If the following words are displayed on the COM serial port, the dial is successful.
Relay etherb ppp_device
Relay ppp_device
DNS server address set to 202.96.64.68.
4) if you want to go offline, remember to enter this step to omit it)
192.168.1.1> ppp 1 disable
==> It is equivalent to interrupting pppoe online, which is very important for users who access the Internet on time.
5) If you want to enable automatic dial-up access after each modem restart, enter
192.168.1.1> config save
6) after success, turn off the MODEM power and restart the MODEM.
Now you don't have to use a proxy server to create a LAN. Please try it! In addition, this function can only be implemented in versions 3. * or later. Note: ETEK TD-2001 ADSL Modem URL: http://www.etek-td.com)
Possible disadvantages:
1. It is basically stable and occasionally dropped once or twice. Turn off the modem for about 10 seconds and start it again!
2. NETMEETING calls are not supported after built-in PPPOE sharing;
3. You cannot use VPN, so you cannot access the company's LAN at home;
4. You cannot use the voice call function of msn or yahoo, or make a network call.
Installation of ZTE ZXDSL831 Modem
1. Set the IP address in the TCP/IP attribute of the NIC connected to the ZXDSL 831 adsl modem to automatic acquisition, DNS, and gateway.
Are not set.
2. Enter 192.168.1.1 in the address bar of the browser and press Enter. The default user name and password are both ZXDSL.
3. Specific settings:
Method 1: Bridging Mode + PPPoE dialing software:
A: Go to "Bridging-> atm vc ";
B: select the link whose vpi/vci is 8/81 and modify and edit it. the vpi/vci is 0/338/35) and press "OK.
C: Enter "Admin-> Commit & Reboot", select "Reboot" in "Reboot Mode", and then press "OK ".
Prompt "changed successfully" and press "restart" to change the ADSL Modem
D: Install and dial the software.
Method 2: built-in PPPoE dialing method:
A: Go to "WAN-> atm vc ";
B: select the link whose vpi/vci is 8/81 and modify and edit it. the vpi/vci is 0/338/35) and press "OK.
C: Go to "WAN-> PPP" and click "add.
The identifier of the link for the atm vc to select vpi/vci as 0/338/35;
Select "Public" for IPF Type ";
Select "Start" or "StartOnDate" for Status ";
Select PPPoE for Protocol;
Use DNS select Enable;
Select Enable for Default Route;
Select CHAP for Security Protocol;
Enter the user Name required for dialing in Login Name;
Enter the Password required for dialing in Password;
Click OK.
D: Go to "Admin-> Commit & Reboot", select "Reboot" in "Reboot Mode", and press "OK ".
"Changed successfully" and then press "restart" to restart the ADSL Modem and then access the internet.