Configuration of brocade 300 optical fiber switch

Configuration of brocade 300 optical fiber switch
I. Mounting
1. New Fiber Optic Switches are available

Note that the network port and Management port are different

2. wired

Ii. basic configuration
1. Configure IP address and Change User Password
A. The default ip address of the new optical fiber switch is 10.77.77.77. You need to configure the ip address for direct connection.

B. log on to the machine and configure the ip address. Username: admin. The default password is password.

C. The logon interface is as follows. The IP address and logon username are displayed in the lower right corner.

D. Modify the ip address and User Password
"Manage" refers to "Switch Admin" refers to "Network"/"User"

E. The following message is displayed after the modification. You need to log on again.

2. enable port
A. "Manage" refers to "Port Admin", view Speed (Gb/s), Port Status, and click "Enable" (you need to plug the fiber optic cable and Enable it based on the corresponding Port)

B. Check the machine status

3. Configure the Zone

1. Create Alias

First, we need to find the WWN Number of the fiber optic card of the host device:

In linux, you can use the following command to query

[14:19:21 root()@storedg host1]# cd /sys/class/fc_host/host1/[14:19:34 root()@storedg host1]# cat port_name0x21000024ff0a6767

[14:20:29 root()@storedg host2]# cat port_name0x21000024ff0a7aa2

You can use the following command to query the AIX system:

[14:22:27 root @ vposdb1/] # lsdev-Cc adapter-S a | grep fcsfcs0 Available 04-08 FC Adapterfcs1 Available 04-09 FC Adapterfcs2 Available 02-08 FC Adapterfcs3 Available 02-09 FC Adapter [14:22:40 root @ vposdb1/] # lscfg-vpl fcs0 fcs0 U78A0.001.DNWKYDT-P1-C4-T1 FC Adapter Part Number ................. 03N5029 EC Level .................... A Serial Number ............... 1d6380c6 Manufacturer ................ 001D Customer Card ID Number ..... 5759 FRU Number .................. 03N5029 Device Specific. (ZM )........ 3 Network Address ............. 000c95a933e ROS Level and ID ............ 02C82774 Device Specific. (Z0 )........ 1036406D Device Specific. (Z1 )........ 00000000 Device specian. (Z2 )........ 00000000 Device specian. (Z3 )........ 03000909 Device specian. (Z4 )........ FFC01231 Device Specific. (Z5 )........ 02C82774 Device Specific. (Z6 )........ 06c000015 Device Specific. (Z7 )........ 07C12774 Device Specific. (Z8 )........ 200010000c95a933e Device Specific. (Z9 )........ BS2.71X4 Device Specific. (ZA )........ b1F2.70A5 Device Specific. (ZB )........ b2F2.71X4 Device Specific. (ZC )........ 00000000 Hardware Location Code ...... u78A0.001.DNWKYDT-P1-C4-T1 platform specific Name: fiber-channel Model: LP11000 Node: fiber-channel @ 1 Device Type: fcp Physical Location: U78A0.001.DNWKYDT-P1-C4-Ta. "Manage" refers to "Zone Admin" refers to "Alias", which divides zones with WWN addresses. The command format is "server name_corresponding HbA"

After finding the WWN, go to the management interface of the optical fiber switch.

B. In Port & Attached Devices (28 Members) on the left, select the corresponding Port and click Add Member to Add the Port to a zone to the Alias Members on the right.

2. Create a Zone
A. "Manage" refers to "Zone Admin" refers to "Zone", which is divided according to Alias, name format: "server name_corresponding HbA _ storage name_corresponding to port 0 controller _ corresponding to Port 1 controller"

B. Add a Zone based on Alias

When creating a zone, you need to add the alias of the host hosts card and the stored alias to the same zone.

3. Create Zone Config
A. "Manage" refers to "Zone Admin" refers to "Zone Config"

B. Use the default configure, select the created Zones name, click "Add member", and Add the zone to config members.

C. Save the configuration. Pay attention to the status bar below. If "end of commit;" appears, it indicates that the configuration is saved successfully.


D. Enable Configuration

After the configuration is complete, configure the storage