Create detailed configuration and screenshots of VLANs, trunk links, and participating Ethernet bundles

Creating VLANs, trunk links, and participating Ethernet bundles

First create the topology:

650) this.width=650; "src=" Http://s3.51cto.com/wyfs02/M00/59/F9/wKiom1TxbJTg6UZ1AAEwCUcZPVs034.jpg "title=" Picture 1.png "alt=" Wkiom1txbjtg6uz1aaewcuczpvs034.jpg "/>

for each Add a virtual network card to the PC

650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M01/59/F5/wKioL1TxbaLghWC8AAHGjFqqC9o667.jpg "style=" float: none; "title=" Image 2.png "alt=" Wkiol1txbalghwc8aahgjfqqc9o667.jpg "/>

The connection topology line 650) this.width=650 should be required for experiment ; "Src=" http://s3.51cto.com/wyfs02/M01/59/F9/ Wkiom1txbjxyjw9faair4hlmn5y385.jpg "style=" Float:none; "title=" Image 10.png "alt=" />

Configure VLAN to switch 1 and add the appropriate ports to the VLAN

650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M02/59/F5/wKioL1TxbaTgdhgbAAKcv92ilCY314.jpg "style=" float: none; "title=" Image 11.png "alt=" Wkiol1txbatgdhgbaakcv92ilcy314.jpg "/>

View configuration of the VLAN

650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M02/59/F9/wKiom1TxbJbSFypNAAJvxF85zmg050.jpg "style=" float: none; "title=" Image 12.png "alt=" Wkiom1txbjbsfypnaajvxf85zmg050.jpg "/>

Trunk Relay link configuration and select package type

650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M00/59/F5/wKioL1TxbaTzIMEaAAGU2g81Cm8853.jpg "style=" float: none; "title=" Image 13.png "alt=" Wkiol1txbatzimeaaagu2g81cm8853.jpg "/>

Bundle the Ethernet channel (note that it is bundled two times)

650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M00/59/F9/wKiom1TxbJeCxCgYAARgF6z7qnk917.jpg "style=" float: none; "title=" Image 14.png "alt=" Wkiom1txbjecxcgyaargf6z7qnk917.jpg "/>

in the Configure VLANs on SW2 and join VLANs, view VLANs

650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M01/59/F5/wKioL1TxbaXgTW2DAAJtEpXZ5hM076.jpg "style=" float: none; "title=" Image 15.png "alt=" Wkiol1txbaxgtw2daajtepxz5hm076.jpg "/>

Configuration trunk, select the package type, and do the Ethernet bundle

650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M01/59/F9/wKiom1TxbJmQNZCUAAHTFCXPIh4734.jpg "style=" float: none; "title=" Image 16.png "alt=" Wkiom1txbjmqnzcuaahtfcxpih4734.jpg "/>

To view bundled Ethernet channels

650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M02/59/F5/wKioL1TxbafxUOP4AAHZ0MIOLY4869.jpg "style=" float: none; "title=" Image 17.png "alt=" Wkiol1txbafxuop4aahz0mioly4869.jpg "/>

in the the configuration done on the SW3 is basically the same as the SW2, so the best trunk and Ethernet one go are the case.

Also, note that the 2nd Ethernet channel is tied up here.

650) this.width=650; "src=" Http://s3.51cto.com/wyfs02/M00/59/F6/wKioL1TxfTmitV5-AARhp-y7iSk401.jpg "title=" Picture 18.png "alt=" Wkiol1txftmitv5-aarhp-y7isk401.jpg "/>

Using Vpcs to assign IP addresses and test connectivity to a virtual network card

If you turn off VPCS again, you need to reconfigure the IP address

650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M00/59/F5/wKioL1TxbajhLHgBAAI8fyQTTRQ845.jpg "style=" float: none; "title=" Image 19.png "alt=" Wkiol1txbajhlhgbaai8fyqttrq845.jpg "/>

Use vpcs ping other PC test Connectivity

650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M00/59/F9/wKiom1TxbJuj9I5BAALhmOYMwoc460.jpg "style=" float: none; "title=" Image 20.png "alt=" Wkiom1txbjuj9i5baalhmoymwoc460.jpg "/>

Test results only 1.1 and 1.3 Pass,1.2 and 1.4 can pass, all the others do not pass OK

This article is from the "My World" blog, please be sure to keep this source http://zhang2015.blog.51cto.com/9735109/1615982

Create a detailed configuration of VLANs, trunk links, and participating Ethernet bundles and