D-link Wireless Router installation in several minutes (1)

Source: Internet
Author: User

In the Internet era, we often encounter D-Link wireless routers.The following describes the knowledge about D_Link wireless router installation, including how to connect DI-524M Wireless Broadband Router to your network and so on.

1: connect DI-524M Wireless Broadband Router to your network

1. First insert the 12 v ac power adapter connector of the DI-524M into the power Jack of the rear panel of the DI-524M, the other end is connected to the power outlet. When Power is on, the Power indicator on the front panel is on. Wait until the DI-524M is started.

2. Connect the network line connecting to the DSL/Cable Modem to the wan end of the DI-524M, that is, the Internet port ).

3. Connect the network cables connected to the computer or other devices to the LAN ~ 4 ports) any port. The panel light for the DI-524M should be:

1) power indicator: hengliang;

2) system status indicator light: flashes every second;

3) WAN port indicator light: flashing from time to time;

4) wireless network indicator light: flickering from time to time;

5) LAN port indicator light: flashing to a computer from time to time)

4. Place the computer with the wireless Nic installed near the DI-524M, wireless network settings for the wireless nic and DI-524M, see the instructions in the following section.

2. Connect other computers to DI-524M

With other ethernet cables, connect other computers with Ethernet interfaces that require access through the DI-524M Wireless Broadband Router to the remaining three lanports on the rear panel of the DI-524M; you can also place a computer with a wireless Nic installed near a DI-524M to access the Internet through it.

Follow the two steps above to connect to the D-Link Wireless RouterAfter, your current network architecture should be the way, or if you are a residential area to be extended, may directly connect the network cable to the wan end of the DI-524M, instead of access Modem, A wired PC is connected to one of the LAN ports of the DI-524M, and a wireless PC is connected to the DI-524M wirelessly through a wireless Nic connected to the computer.

3. When configuring local connection, connect the PC to one of the LAN ports of the DI-524M through the network cable)

1. First, check the IP address of your computer's local connection.

1) on the desktop of your computer, right-click "Network neighbors" and select "properties ". The "network connection" window is displayed.

2) Right-click Local Connection-Properties

3) in the "Local Connection Properties" dialog box that will pop up later, select Internet protocol TCP/IP), and then click the attribute button below.

In the window that will be opened later, select "automatically obtain IP Address", click OK, and then return to the previous interface and click Close. When your computer is connected to the DI-524M, the computer automatically gets the IP address.

2. Wait about 15 seconds. When the local connection shows that the connection is connected, click Start-run, Enter cmd in open, and click OK.

Enter the MS-DOS Command Prompt window, type ping 192.168.0.1 and press Enter. If Reply from 192.168.0.1: bytes = 32 time <1 ms TTL = 64 appears, it indicates that the computer has been connected to the DI-524M, you can perform the next step. If the above information does not appear, you can check the cause through the FAQ on the www.dlink.com.cn website due to our frequently asked questions, if you have not found this issue for the FAQ under the DI-524M product, you can refer to the related information in the DI-624 + A product FAQ ).

4. DI-524M Wireless Router Network Configuration

Open a browser. This document uses ie as an example. Enter 192.168.0.1 in the address bar of the browser and press Enter. If the browser is not connected to the Internet, you can open the router configuration interface as long as you use a network cable to connect one of your PC and the lanport of the router, or wirelessly connect to the router configuration interface, But When configuring the router, please use a wired connection to the DI-524M ). On the displayed page, enter admin as the user name. The password is blank by default. Then, click Login to enter the following configuration interface. From this interface, you can set the network connection of the vro in two ways: Use the Configuration Wizard, and use manual configuration. If you only need to configure the WAN port, use the settings wizard. The following describes how to use the Configuration Wizard.


Contact Us

The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion; products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the content of the page makes you feel confusing, please write us an email, we will handle the problem within 5 days after receiving your email.

If you find any instances of plagiarism from the community, please send an email to: info-contact@alibabacloud.com and provide relevant evidence. A staff member will contact you within 5 working days.

A Free Trial That Lets You Build Big!

Start building with 50+ products and up to 12 months usage for Elastic Compute Service

  • Sales Support

    1 on 1 presale consultation

  • After-Sales Support

    24/7 Technical Support 6 Free Tickets per Quarter Faster Response

  • Alibaba Cloud offers highly flexible support services tailored to meet your exact needs.