dellr720-configuration of system operation and maintenance Broadcom NIC group configuration instance

First, the configuration of the port group in the actual situation of the use of many scenarios, partial redundancy mainly to solve the single point of failure. Many are in combination with Ha, VRRP, HSRP, switch stacking and many other practical scenarios.

All right, no nagging, just "meal".

The first step:

Configuration Broadcom NIC Group

to broadcombroadcom NIC management software Span style= "font-family: ' Microsoft Jas Black ', ' Microsoft Yahei '; font-size:12px;line-height:125%;" >bacs ( broadcom Advanced Control Suite from broadcom

http://www.broadcom.com/support/ethernet_nic/netxtreme_server.php

Select the corresponding version of the download link to download.

650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M02/6E/7E/wKioL1V-h-eDf4GHAAG1ZUK6T88540.jpg "title=" 1.png " alt= "Wkiol1v-h-edf4ghaag1zuk6t88540.jpg"/>

Run after decompression Setup installs , installs the basp in Control Suite, and uses the default options during installation. The installation process is slightly.

Second step:

when the installation is complete, start from the Start menu BACS

650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M02/6E/82/wKiom1V-hmOAkwR7AADSkSCsCL4789.jpg "title=" 2.png " alt= "Wkiom1v-hmoakwr7aadskscscl4789.jpg"/>

Third Step:

Click Teams to Goto team View, switch to the NIC group views;

650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M01/6E/7E/wKioL1V-iEnChFRXAAECFO7l60I441.jpg "title=" 3.png " alt= "Wkiol1v-ienchfrxaaecfo7l60i441.jpg"/>

Step Four:

Right-click Teams-->create Team, start the Network Card Group Creation wizard;

650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M02/6E/7E/wKioL1V-iGSBO0-rAADa1mA4EYA220.jpg "title=" 4.png " alt= "Wkiol1v-igsbo0-raada1ma4eya220.jpg"/>

Step Five:

Click Next, which is configured through Wizard mode. Or click on Expert mode to configure it with the experts. For ease of understanding, the following will be described in Wizard mode;

650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M00/6E/82/wKiom1V-htmwumSTAAGHFCMtEJw825.jpg "title=" 5.png " alt= "Wkiom1v-htmwumstaaghfcmtejw825.jpg"/>

Step Six:

Enter the network card group name, note that the following prompt indicates that the name of the naming restrictions, not more than four characters, cannot use \ \:* and other special characters;

650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M01/6E/7E/wKioL1V-iNmyk4oFAAFOif1PBOw260.jpg "title=" 6.png " alt= "Wkiol1v-inmyk4ofaafoif1pbow260.jpg"/>

Seventh Step:

Select the NIC group type, There are three types of Broadcom NIC bindings,

Smart load Balancing (TM) and Failover (SLB): An Intelligent workload balancing mode .

8023.3AD link Aggregation using link Aggregation controlprotocol (LACP): dynamic Link Aggregation mode requires the switch to turn on LACP ( Dynamic Link aggregation ), using this aggregation mode, if the switch does not support LACP or support LACP but does not open, then the network card link will only display 1Gbps.

FEC/EGC Generic trunking: static link Aggregation mode , select this if the switch does not have LACP mode. With this aggregation mode, regardless of whether your switch supports convergence or not , LACP is supported, then the rate at which theNIC number *1gbps will be displayed .

If no special instructions are used, the recommended SLB mode, intelligent load balancing and failover.

650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M01/6E/83/wKiom1V-h2zzLHEWAAG_bSzousE025.jpg "title=" 7.png " alt= "Wkiom1v-h2zzlhewaag_bszouse025.jpg"/>

Eighth Step:

Select the network card you want to add to the NIC group, click ADD , click When you are finished adding Next . 4 Nic , it is recommended to create a network card group per 2 network cards, can meet the load balancing and failover requirements;

650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M02/6E/7E/wKioL1V-iWfjjZDXAAKWLspbqbo213.jpg "title=" 8.png " alt= "Wkiol1v-iwfjjzdxaakwlspbqbo213.jpg"/>

Nineth Step:

Two NIC bindings, do not need to specify an alternate member, if there is more than one NIC binding, it is recommended to specify a network card as an alternate member. When there is a problem with load balancing, the standby member will be responsible for traffic flow;

650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M01/6E/7E/wKioL1V-iZaBPbRLAAGuVcf1154391.jpg "title=" 9.png " alt= "Wkiol1v-izabpbrlaaguvcf1154391.jpg"/>

Tenth step:

Configuration Livelink, this feature will continue to ping a specified IP address to detect link status, because it will have a certain impact on the network, it is recommended to remain closed (the default option);

650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M02/6E/83/wKiom1V-iA_SklEWAAFy53Z0ElE403.jpg "title=" 10.png "alt=" Wkiom1v-ia_sklewaafy53z0ele403.jpg "/>

11th Step:

determine whether a network adapter is specified as required VLAN;

650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M01/6E/7F/wKioL1V-iduSlKNdAAEr_TcxIW8076.jpg "title=" 11.png "alt=" Wkiol1v-iduslkndaaer_tcxiw8076.jpg "/>

12th Step:

Click Finish commits the configuration change. To continue configuring additional NIC groups, select Save changes and Continue tomanage more teams and click Nextto repeat the above configuration steps.

650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M01/6E/83/wKiom1V-iFXQp-wwAAGU05zbAb0925.jpg "title=" 12.png "alt=" Wkiom1v-ifxqp-wwaagu05zbab0925.jpg "/>

One final step:

after the configuration is complete, locate the created NIC group in the Control Panel- network connection and configure it according to the IP configuration of the normal network card .

Okay, here, all configurations are complete.

Here, emphasize a little. After we configured it last night, please simulate a single point of failure for debugging. Avoid pitfalls.

The default use of Windows is failover, and if you choose the load mode, it involves the link bundle of the "stack" switch on the uplink.

As for the advanced features, please take full advantage of the imagination of the Siege division, to do the program!!

This article from "from Zero to One" blog, reproduced please contact the author!

dellr720-configuration of system operation and maintenance Broadcom NIC group configuration instance