Detailed description of ZTE models using wireless route settings

Experience in configuring wireless routing ZTE models, network parameter settings in wireless routing settings experience, LAN port parameter settings, and SSID settings will be the focus of this article, I hope you will have a clear understanding after reading the following articles.

Yesterday, I helped my friend set up an experience in setting up wireless routing. I am an ADSL cat from Taizhou Telecom. I have four LAN ports. The model is ZTE ZXDSL 531B and the software version is ZXDSL 531BIIV2. 2.0a _ E17. I can't find any experience in setting broadband wireless routes on the console to share the Internet Settings. China Telecom is so cool! Right away, Google, the power of the people is infinite. Find an article specifically about the 531B attack method and crack the wireless Cat sent by China Telecom.) Complete the settings as follows:

Connect the telephone line and network cable, enable the wireless route settings experience, set the computer's IP address to automatically get, or manually specify the IP address as 192.168.1.x. Note: x is a number greater than 2 and less than 254 that is not used by other computers). The subnet mask is 255.255.255.0. Open the browser on your computer and enter "http: // 192.168.1.1 "the username and password are admin.

Go to quick configuration and set relevant information. Users of Taizhou Telecom note that VPI is set to 8, VCI is set to 81, and other settings can be used by default. In the last step, click "application" instead of "application". Instead, right-click to view page properties and obtain the URL of the page. This URL contains all the quick settings, modify the following items in the URL:
◆ Accessmode = pppoe
◆ Iptype = dhcp
◆ Nat_enable = true

The modified URL may be like this:
◆ Http: // 192.168.1.1/webconfig/quick/quickConfirm.html? PageAction = quick & vpi = 8 & vci = 81 & scat = UBR
◆ & Scr = 0 & pcr = 0 & mbs = 0 & accessmode = pppoe & encap = llc & iptype = dhcp & dnstype = autoDNS & nat_enable = true
◆ & BundleMode = bundleDisabled & eth0_enable = 0 & eth1_enable = 0 & eth2_enable = 0 & eth3_enable = 0 & wlan_enable = 0
◆ & Amp; usb_enable = 0 & amp; ethIpAddress = 192.168.1.1 & amp; ethSubnetMask = 255.255.255.0 & amp; lanMtu = 1500 & amp; startIp = 192.168.1.2
◆ & EndIp = 192.168.1.254 & time_dd = 1 & time_hh = 0 & time_mm = 0 & dhcpserver = dhcpEnabled & virtual_Ip = false

For the layout, We need to divide it into five lines. The lines that are actually put in the address bar are connected in the middle without spaces. Enter the modified URL in the address bar of the browser and press Enter, the Modem is reconfigured. After about 30 seconds, you can re-enter the Modem Web Console. Then you can see that there is only one PPPOE connection in the WAN configuration. The connection name is pppoe_8_81. There is a "connection" button below. Click Connect and enter the ADSL user name and password to connect.
 
If everything goes well, when you return to the WAN interface, you can see that the original "connection" has changed to "disconnected", indicating that the ADSL cat has successfully achieved a dial-up connection. In this case, you can try to use Modem route to access the Internet. If the access to the network is unsuccessful, it is generally because there is no automatic wireless route setting experience table after Modem dial-up, resulting in Internet access failure. In this case, you need to use telnet to log on to the Modem for further settings. The method is to enter the DOS command prompt, click Start Menu, run, Enter cmd, and press Enter)
◆ Input
◆ Telnet 192.168.1.1
◆ Telnet to vrotelnet)
◆ Input
◆ Ip add route ppproute 0.0.0.0 0.0.0.0 interface IpPppoe_8_81

Add the route to the route table. Note that the final IpPppoe_8_81 is determined by the connected vpi and vci. The format is IpPppoe_vpi _ vci, and then you can access the Internet normally, by default, UPNP is disabled. If you need to enable upnp, enter UPNP set device igd enabled in telnet to enable upnp.) then, enter UPNP show info. You can see that UPNP is enabled.

After configuring wireless routing, you can go back to the Web Console to perform other wireless and user management settings. After completing the settings, go to the backup configuration page and back up the configuration to your local device, in the future, if the configuration is messy, you can directly restore the backup configuration. You do not have to perform the configuration again. With the preceding settings, ZXDSL 531B can be used as a Broadband Router to allow multiple computers to access the Internet.

The only drawback is that automatic dial-up is not implemented, and of course there is no automatic reconnection function for disconnection. You need to enter the "connection" in the Wide Area Network on the management interface to dial up. It is estimated that you can set it through telnet, if anyone finds it, leave a message and tell me, thank you. The content of this article is based on the fact that some netizens have cracked the wireless Cat sent by China Telecom and adapted it based on the actual situation set by Taizhou Telecom ADSL. Thanks to the original author!