Device Configuration Routing restore factory and modify privileged password

First, the router to restore the factory settings

router>en

Router#config

Configuring from terminal, memory, or network [terminal]?

Enter configuration commands, one per line. End with cntl/z.

Router (config) #

Router (config) #interface f0/0

Router (config-if) #

Router (config-if) #ip address 192.168.1.1 255.255.255.0

Router (config-if) #no shutdown

%link-5-changed:interface fastethernet0/0, CHANGED state-to-up

Router (config-if) #

Router (config-if) #^z

router#

%sys-5-config_i:configured from console by console

router#

Router#erase Startup-config

Erasing the NVRAM filesystem would remove all configuration files! Continue? [Confirm]

[OK]

Erase of Nvram:complete

%sys-7-nv_block_init:initialized the geometry of NVRAM

router#

Router#reload

Proceed with reload? [Confirm]

%sys-5-reload:reload requested by console. Reload reason:reload Command.

System Bootstrap, Version 12.3 (8r) T8, RELEASE Software (FC1)

Cisco 1841 (Revision 5.0) with 114688k/16384k bytes of memory.

Self decompressing the Image:

########################################################################## [OK]

Restricted Rights Legend

---System Configuration Dialog---

Continue with Configuration dialog? [Yes/no]: N

Press RETURN to get started!

Router>

router>en

router#

Router#show Running-config

Hostname Router

!

Spanning-tree Mode Pvst

!

Interface fastethernet0/0

No IP address

Duplex Auto

Speed auto

Shutdown

End

Second, modify the privileged password

Router>

router>en

router#

Router#config

Configuring from terminal, memory, or network [terminal]?

Enter configuration commands, one per line. End with cntl/z.

Router (config) #

Router (config) #enable password 123

Router (config) #^z

router#

%sys-5-config_i:configured from console by console

router#

Router#write Memory

Building configuration ...

[OK]

Router#reload

Proceed with reload? [Confirm]

%sys-5-reload:reload requested by console. Reload reason:reload Command.

##########

Monitor:command "Boot" aborted due to user interrupt

Rommon 1 > Confreg 0x2142

Rommon 2 > Reset

System Bootstrap, Version 12.1 (3r) T2, RELEASE Software (FC1)

Copyright (c) by Cisco Systems, Inc.

Cisco 2621 (MPC860) Processor (revision 0x200) with 253952k/8192k bytes of memory

Self decompressing the Image:

########################################################################## [OK]

Restricted Rights Legend

---System Configuration Dialog---

Continue with Configuration dialog? [Yes/no]: N

Press RETURN to get started!

Router>

router>en

router#

Router#config

Configuring from terminal, memory, or network [terminal]?

Enter configuration commands, one per line. End with cntl/z.

Router (config) #enable p Sisco

Router (config) #^z

router#

%sys-5-config_i:configured from console by console

router#

Router#write Memory

Building configuration ...

[OK]

Router#reload

Proceed with reload? [Confirm]

%sys-5-reload:reload requested by console. Reload reason:reload Command.

Self decompressing the Image:

#######

Monitor:command "Boot" aborted due to user interrupt

Rommon 1 > Confreg 0x2102

Rommon 2 > Reset

System Bootstrap, Version 12.1 (3r) T2, RELEASE Software (FC1)

Copyright (c) by Cisco Systems, Inc.

Cisco 2621 (MPC860) Processor (revision 0x200) with 253952k/8192k bytes of memory

Self decompressing the Image:

########################################################################## [OK

This article is from the "it Female nerves" blog, so be sure to keep this source http://liyaqi.blog.51cto.com/9976294/1621592

Device Configuration Routing restore factory and modify privileged password