Differences and features of Layer 2, Layer 3, and Layer 4 switches

Layer-2, layer-3, and layer-4 switches have different characteristics. layer-2 switching is a mature technology. A layer-2 switch is a data link layer device that can identify MAC address information in data packets, forward based on the MAC address, and record these MAC addresses and corresponding ports in an internal address table. The specific workflow is as follows: (1) When the switch receives a packet from a port, it first reads the source MAC address from the packet header, in this way, it will know the port on which the machine with the source MAC address is connected; www.2cto.com (2) will read the destination MAC address in the packet header, and find the corresponding port in the address table; (3) If the table contains a port corresponding to the destination MAC address, copy the data packet directly to the port. (4) if the corresponding port is not found in the table, the packet is broadcast to all ports. When the target machine responds to the source machine, the switch can learn which port the target MAC address corresponds, the next time you transmit data, you no longer need to broadcast all ports. In this process, the MAC address information of the entire network can be learned. The second-layer switch creates and maintains its own address table. The working principle of a L2 Switch can be inferred from the following three points: (1) because the switch exchanges data on most ports at the same time, a wide switching bus bandwidth is required, if a L2 Switch has N ports, and the bandwidth of each port is M, and the bandwidth of the switch bus exceeds N × M, the switch can achieve line rate switching. (2) the MAC address of the machine connected by the Learning port, which is written to the address table, and the size of the address table (generally two Representation Methods: one is beffer ram, and the other is the MAC table item value ), the size of the address table affects the access capacity of the switch. www.2cto.com (3) Another layer-2 switch generally contains an ASIC (Application specific Integrated Circuit) chip used to process data packet forwarding, therefore, the forwarding speed can be very fast. Because different manufacturers use different ASIC, the product performance is directly affected. The above three points are also the main technical parameters used to judge the performance of Layer 2 and Layer 3 switches. Please pay attention to the comparison when considering device selection. (2) routing technology routers work on the layer 3-Network Layer * of the OSI model. The working mode of routers is similar to that of Layer 2 switches. However, routers work on Layer 3, this difference determines that routes and switches use different control information when passing packets, and the implementation methods are different. The working principle is that there is also a table inside the vro, which indicates that if you want to go to a certain place, the next step should be to go there, if you can find the data packet from the routing table, add the link layer information and forward it. If you do not know where the next step is, discard the package and return a message to the source address. In essence, the routing technology has two features: determining the optimal route and forwarding data packets. Various information is written into the routing table. The routing algorithm calculates the Optimal Path to the destination address, and then sends data packets through a simple and direct forwarding mechanism. The next vro that receives data continues to forward according to the same working method, and so on until the data packet reaches the destination vro. There are two different ways to maintain the route table. One is to update the route information, publish some or all of the route information, and the router learns route information from each other to master the topology of the whole network, this type of routing protocol is called the distance vector routing protocol. The other is that the router broadcasts its own link status information and learns from each other to learn route information across the network, then, the optimal forwarding path is calculated. This type of routing protocol is called the Link State routing protocol. Www.2cto.com because a vro requires a lot of path computing work, the performance of a general processor is directly determined by its performance. Of course, this judgment is still for low-end routers, because high-end routers often adopt distributed processing system design. (3) In recent years, the three-layer exchange technology has been publicized everywhere. Some people say this is a very new technology. Some people also say that it is a three-layer exchange technology, there is no new things in the stack of routers and L2 switches. Is that true? Next, let's take a look at the working process of a layer-3 Switch through a simple network. For devices that use IP addresses, A ------------------------ layer-3 switches ---------------------- if device B uses IP addresses, for example, A wants to send data to Device B. If the destination IP address is known, A obtains the network address using the subnet mask, determine whether the destination IP address is in the same CIDR block as the target IP address. If A is in the same network segment but does not know the MAC address required for data forwarding, A sends an ARP request, B returns its MAC address, and A uses this MAC encapsulation packet to send it to the switch concurrently, the second-layer switch module is used to find the MAC address table and forward data packets to the corresponding port. If the destination IP address is not displayed in the same CIDR block, A needs to communicate with B, and there is no corresponding MAC address entry in the stream cache entry, the first normal data packet is sent to a default gateway. This default gateway is usually set in the * system and corresponds to the layer-3 routing module. Therefore, for data that is not in the same subnet, the MAC address of the default gateway is first placed in the MAC table. Then, the layer-3 module receives the packet and queries the route table to determine the route to B. A new frame header is constructed, the MAC address of the default gateway is the source MAC address, and the MAC address of host B is the target MAC address. Through A certain identification trigger mechanism, it establishes the MAC address and forwarding port correspondence between host A and host B, and records the data from host A to host B in the stream cache entry table, it is directly submitted to the layer-2 Switching Module. This is generally referred to as one-time route forwarding. Www.2cto.com and above are a brief summary of the three-layer switch operation process. We can see the characteristics of the three-layer switch: the hardware is combined to achieve high-speed data forwarding. This is not a simple superposition of Layer 2 switches and routers. The Layer 3 routing module is directly superimposed on the Layer 2 switching high-speed backplane bus, breaking through the interface speed limit of traditional routers, the speed can reach dozens of Gbit/s. Calculating the backboard bandwidth is two important parameters for the performance of a layer-3 switch. The simple routing software simplifies the routing process. Most of the data forwarding, except for the necessary route selection, is handled by the routing software, and is a layer-2 module for high-speed forwarding. Most of the routing software is an efficient optimization software that has been processed, it is not a simple copy of the software in the router. Conclusion L2 switches are used in small local networks. There is no need to talk about this. In a small LAN, broadcast packets have little impact, the two-layer switch's fast switching function, multiple access ports, and low price provide a perfect solution for small network users. The advantage of a vro lies in its rich interface types, powerful three-tier functions, and powerful routing capabilities. It is suitable for routing between large networks. Its advantage lies in the selection of the best route and load balancing, router functions such as link backup and exchange of route information with other networks. The most important function of the www.2cto.com layer-3 switch is to speed up data forwarding within a large local area network. The routing function is also used for this purpose. If a large network is divided into small local networks by department, region, and other factors, this will lead to a large number of Internet mutual access. Simply using a layer-2 switch cannot achieve Internet mutual access. For example, simply using a router, due to the limited number of interfaces and slow route forwarding speed, the network speed and network scale will be limited. Using a layer-3 switch with the routing function for fast forwarding will become the first choice. In general, in a network with a large volume of intranet data streams and fast response requirements, if all three-layer switches do this, the layer-3 switches will be overloaded and the response speed will be affected, it is a good networking strategy to make full use of the advantages of different devices by handing over the routes between networks to routers. Of course, the premise is that the customer's pockets are great; otherwise, they will leave for the second place, the layer-3 switch is also connected to the Internet. A simple definition of layer-4 switching is that it is a function that determines that transmission is not only based on the MAC address (layer-2 Bridge) or the source/Target IP address (layer-3 route ), based on the TCP/UDP (Layer 4) application port number. The layer-4 switching function is like a virtual IP address pointing to a physical server. Its transmission services are subject to a variety of protocols, including HTTP, FTP, NFS, Telnet, or other protocols. These services require complex load balancing algorithms based on physical servers. In the IP address world, the service type is determined by the TCP or UDP port address of the terminal. The application interval in the layer-4 switch is jointly determined by the source and terminal IP addresses, TCP and UDP ports. In the layer-4 switch, a virtual IP address (VIP) is set up for each server group for search. Each group of servers supports an application. Each application server address stored in the Domain Name Server (DNS) is a VIP address, rather than a real server address. When a user applies for an application, a VIP Connection Request (such as a tcp syn Packet) with the target server group is sent to the server switch. The server switch selects the best server in the group, replaces the VIP in the terminal address with the actual Server IP address, and sends the connection request to the server. In this way, all packets in the same range are mapped by the server switch and transmitted between the user and the same server. The principle of layer-4 switching at www.2cto.com the layer-4 of the OSI model is the transport layer. The transport layer is responsible for peer communication, that is, coordinated communication between the network source and the target system. In the IP protocol stack, This is the protocol layer of TCP (a Transport Protocol) and UDP (user data packet protocol. In layer-4, the TCP and UDP headers contain portnumbers, which uniquely differentiate which application protocols (such as HTTP and FTP) are contained in each packet ). The endpoint system uses this information to distinguish packet data, especially the port number, so that a computer system at the receiving end can determine the type of the IP packet it receives and hand it over to appropriate high-level software. A combination of port numbers and device IP addresses is usually called socket )". The port numbers between 1 and 255 are retained. They are called "well-known" ports. That is to say, these port numbers are the same in the TCP/IP protocol stack implementations of all hosts. In addition to the "well-known" port, standard UNIX services are allocated between port 256 and port 1024. custom applications generally allocate port numbers over port 1024. you can find the latest list of allocated port Numbers on RFc1700 "Assigned Numbers. The additional information provided by the TCP/UDP port number can be used by the network switch, which is the basis for layer-3 switching. "Familiar with" port number example: application protocol port number FTP 20 (data) 21 (Control) TELNET 23 SMTP 25 HTTP 80 NNTP 119 NNMP 16 162 (SNMP traps) the additional information provided by the TCP/UDP port number can be used by the network switch, which is the basis for layer-4 switching. A vswitch with the layer-4 function can act as the "virtual IP" (VIP) frontend connected to the server. Each server and server group supporting a single or common application is configured with a VIP address. This VIP address is sent and registered on the domain name system. When a service request is sent, the layer-4 switch identifies the start of a session by determining the start of TCP. Then it uses complex algorithms to determine the best server for processing this request. Once this decision is made, the switch associates the session with a specific IP address and replaces the VIP address on the server with the real IP address of the server. Each layer-4 switch at www.2cto.com stores a source IP address that matches the selected server and a connection table associated with the source TCP port. The layer-4 switch then forwards the connection request to the server. All subsequent packets are reinjected and forwarded between the client and the server until the switch discovers a session. When layer-4 switching is used, the access can be connected to a real server to meet user-defined rules, for example, the number of connections on each server is equal or the transmission stream is allocated based on the capacity of different servers. How to choose the appropriate layer-4 Switching a, the speed in order to be effective in the enterprise network, the layer-4 switching must provide comparable performance with the layer-3 line rate router. That is to say, layer-4 switching must be performed on all ports at full-media speed *, even on multiple Gigabit Ethernet connections. The Gigabit Ethernet speed is equal to the maximum speed of 488000 packets per second (assuming the worst case, that is, all packets are the minimum size defined by the network and are 64 bytes long ). B. The server capacity balancing algorithm is based on the desired capacity balancing interval. There are many algorithms for layer-4 switches to allocate applications to servers, there are simple detection loop recent connections, detection loop latency, or detection server closed loop feedback. Among all predictions, closed-loop feedback provides the most accurate detection that reflects the current business volume of the server. Www.2cto.com c, table capacity should be noted that the switch for layer-4 switching needs to have the ability to distinguish and store a large number of sending table items. This is especially true for vswitches at the core of a CEN instance. The size of many second/third-layer switches tends to be proportional to the number of network devices. For a layer-4 switch, this quantity must be multiplied by the number of different application protocols and Sessions used in the network. Therefore, the size of the table to be sent increases rapidly as the number of device and application types increases. Layer-4 switch designers need to consider this growth when designing their products. The large table capacity is critical to the manufacture of high-performance switches that support line-rate transmission of layer-4 traffic. d. Redundant layer-4 switches support the redundant topology structure. When there is a dual-link network card with fault tolerance connection, it is possible to establish a completely redundant system from a server to the network card, the link and the server switch.