Efficiency source Seagate 7200.1 Read-only fix-smart error

Efficiency source 7200.10 HDD read-only, ATA error handling

Today a 7200.10 data recovery, model number: ST380215A; The firmware version number is:

The 3.AAC;SN number is: 9qz1hp9l. After the drive is connected to the terminal, the status displayed is "Busy".

The information displayed under the instruction is:

The processing of this situation, must be read-only error before the end of the hard disk detection, back to the T-level mode, can do other processing. This dish is a little different from the one we've solved. Now let's introduce the procedure.

First, in the other operations, click "Go to Class F", etc., after completion. Press CTRL + Z or enter in instruction mode to see that it is now in F-class mode.

Next, enter the r instruction under the instruction to read the basic boot parameter module into memory from the hard disk. Then enter "j,,22" in the instruction mode to return to T-level mode.

1

In T-level mode, enter R carriage and read the system parameters from the disk body. If it is a normal hard drive, after entering this command, there will be no error message. There is an error message for this disk, but it has no relationship and does not affect the subsequent operation. For long disks, it is possible that subsequent operations will not continue

.

When finished, then use "ctrl+r" to load the Cert module.

If the "INVALID CERT DISK CODE" is displayed, you will need to boot the CERT module before loading.

When the Cert module is valid, go back to Level 1 mode and enter F return, which is ignored by the write error command. When finished, go back to the T-level and enter "i4,1,22" to clear the G table

After completion, the power is switched off. We find that the same error message is displayed in instruction mode. So we use another method to solve, clear the smart table. In instruction mode, power is switched off. Before the error message, use CTRL + Z to return to T-level mode. Then in Level 1 mode, enter the F command.

Enter "N1" after completion. The hard disk starts to initialize the smart table.

The information under the View command is OK after completion. Exit instruction mode, the status is ready, and the parameters of the hard disk can be recognized. You can read the content again by using the sector view. That means the plate is ready.

2

Common error hints and solutions in Seagate Hard Drive instruction mode (i)

Common error hints and solutions in Seagate Hard Drive instruction mode (i)

Seagate hard disk error judgment, generally in the instruction mode, observing the information displayed under the instructions, through these error prompts, we can probably know the problem of the hard disk. Here's a quick introduction to common error messages

(1)

OVERLAY FAILED

This error message usually occurs in the cool Fish series, and the presence of this error message indicates that the ATA module is faulty or missing. The 1th ATA module needs to be written back to fix this error. Before you write back to ATA, you need to mount the hard disk one time before you can operate. For 7200.7 and before the hard disk, write-back ATA fast, and for 7200.7 after the disk, the write-back speed may be very slow, the progress bar will run many times, it takes about 10 minutes to 20 minutes, please wait patiently. For 7200.7 previous hard drives, if there is no ATA 1th module of the original disk, you can find the same model, the same firmware version number, the same as the first four bits of the SN code back and forth.

(2) STUFF was unreadable

3

This error message for 7200.7 and before the common problem repair can be processed, this error is the parameter module information loss of the hard disk. And after the common fault repair, you need to manually modify the hard drive parameters. Parameters that need to be modified include model number and capacity

For disks after 7200.7, the general requirement is to write back the original disk of module 4th. Module 4th is the parameter module of the hard disk. For 7200.7 after the disk can also be directly used to repair the common problems, but the success rate is not high.

(3)

Not INTERFACE Age

In instruction mode, the "Not INTERFACE age" message is seen after power-on, and there are two possible scenarios: first, the age value is not 60 or 00. This situation can be entered in instruction mode n50,,22, directly back to 50 mode. Or wait for the calibration to end, from age 01 to 4F, the middle step is to calibrate, if the repair disk can let it continue to run, if the data should be terminated immediately. Second, the age of the value of 60 or 00 of the case, the hard disk needs to do automatic calibration or F-level calibration to repair.

Efficiency source Seagate 7200.1 Read-only fix-smart error