Establish a wireless network for TP-link Routing

The establishment of TP-link routing wireless network technology has been constantly in-depth into our daily life, basically every family has set up a wireless network, this article takes TP-link router as an example, I would like to introduce some problems and skills we should pay attention to when setting up a wireless network. Here I will explain in detail some examples, hoping to help you. Www.2cto.com 1. Factors affecting wireless network performance 1. Transmission Power: the transmission power of wireless routes is mostly below 250 mw, and the maximum power of the bridge is mw. 2. antenna type and direction: the performance of The Omnidirectional antenna is poor, and the transmission rate of the antenna is higher. Generally, the omnidirectional antenna is used for wireless routing and the oriented antenna is used for wireless clients. 3. Noise and interference: microwave ovens, wireless phones, the same or adjacent Wireless AP channels, etc., will have an important impact on the transmission rate. 4. Building Structure: After the wireless signal is reflected multiple times in the building, when a wireless device arrives, it can cause multi-path transmission and mutual interference. In addition, when wireless signals penetrate the wall, there will be a large loss.
5. Wireless route position: the Wireless AP should be placed in a high position to avoid blocking other objects. When a wireless antenna is placed at the same horizontal position, the signal strength is the highest. 6. Connection loss: Connection Head Loss and feeder loss between the wireless network card and the wireless antenna, it will also weaken the wireless signal www.2cto.com to a certain extent. 2. Poor wall-crossing capability of the wireless network. A wireless network is formed in the floor, and most laptops can be connected normally, there are only a few walls between laptops and wireless routes. Although they are still within the effective coverage range, wireless signals are weak, network communication is interrupted and the transmission rate is extremely low.
1. Generally, radio waves cannot pass through the wall, and signals can still be transmitted across the wall, not because the signals pass through the wall, instead, the signal is reflected in the room many times from the place of the door or the place with a window, so we can consider the enhancement effect from two aspects, because the communication after the wall is actually communication in the shadow area, it is obvious that multiple antennas are better than one antenna, and the high-gain antenna is better than the low-gain antenna, high transmit power is better than low transmit power. 2. The penetration capability of wireless signals is limited. If there is wall blocking, wireless signals become weaker, leading to unstable data transmission. The transmission distance must be longer or higher transmission power, you can purchase an independent antenna. Otherwise, the signal transmission speed and stability of wireless products are greatly affected by the environment. 3. Poor performance when using wireless cables at the same time. Two NICs are installed in the computer, one with 100 M built-in and connected to the Intranet through a network cable. the other with a wireless network card connects to the Internet through a wireless router, now, you can access either of the two networks, but cannot connect them to the same network.
1. If there is no need to use two connections in the computer just to share the network connection, you only need to connect the LAN port of the wireless route with the switch, connect the WAN port with the ADSLModem, and then simply set the wireless route to achieve Internet Connection Sharing across the network. No problem is found whether it is wireless access or Ethernet access, in addition, the connection between the wireless network and the Ethernet computer can be realized. 2. Now you can use wireless routes to connect to the Internet, which means that the wireless route has been set up. Therefore, you only need to simply connect the lanport of the wireless route to the Ethernet, it does not need to be as complicated as the above problems. Www.2cto.com 4. The wireless connection between the two buildings has two buildings, with a distance of 80 ~ 100 m. One building has a optical fiber access switch, and the other client needs to use the switch to connect to the Intranet. due to various reasons, wired connections are not allowed, so wireless access is only considered.
1. The valid distance between wireless networks is less than 80 ~ 100 m. Therefore, it is recommended to install an omnidirectional antenna on the Wireless AP end and a targeted antenna on the wireless client to gain wireless signals and improve the network transmission rate. The wireless antenna can use indoor antennas, it is fixed on the window. After a wireless antenna is used, the transmission rate can reach 11 Mbps, 22 Mbps, 44 Mbps, 54Mbps, and 108 Mbps based on the different devices used. 2. In thunderstorms and foggy weather, wireless signals may be affected to some extent. However, due to the proximity, the effect of weather on the transmission rate of wireless networks is negligible, there is no performance difference between the PCI interface and the wireless Nic of the USB interface, and the impact on the wireless network transmission rate is not particularly great.
After reading the above content, I believe you must have some skills and common problems in setting up a wireless network on the TP-link router. If you need it, you can set up a wireless network on your own.