Fireworks FAQ (5)

Source: Internet
Author: User
Tags copy
Solution | Question 24. How to make a seamless tiled background pattern The biggest problem in the new pattern filling process is how to make the picture seamless when the FW fills the area larger than the pattern picture, repeats the pattern picture until it fills the entire object. If the picture uses even the smallest border, after repeated stitching is very obvious, and most of the time, this situation is not enough, there are several ways to avoid the appearance of this seam.

First of all, the easiest way is not to put the graphic no element to the edge of the pattern picture. This allows the canvas (or background color) of each picture to be blended smoothly.

Of course, in many cases the picture has covered the entire background, and the color of the canvas is completely obscured. For this type of graphics to be converted to patterns, must be a certain picture editing work to ensure edge elimination. Luckily, FW has enough graphics editing capabilities to perform this operation. When you tile a picture, each side of the picture will be connected to another picture to eliminate all boundaries, you must simulate a tiled pattern, and then mix the edges of the picture to eliminate the boundary. The following steps are performed to smooth the edges of the pattern in FW:

1. Open the picture file you want to convert to a pattern.

2. Select a part of the picture as the basis of the pattern. Using a scanned picture or part of another graphic as a pattern is a general method. Decide the size of the pattern first (128*128 is a good choice), and then use the options panel to set the appropriate size using the fixed size feature of the Marquee (marquee) tool. This makes it easy to use a preset marquee, and you can move around the graphic flexibly to locate the desired part.

3, select the menu command edit->copy copy selected area.

4, select the menu command file->new create a new document. The document should be at least three times times more than the selected picture. If you select a 128 pixel square picture, the minimum size of the new document is 384*384.

5. For accurate positioning, you can select the menu command View->grid option->edit grid to set the size of the gridline to the size of the selected picture, and select the Show grid and Snap to grid options.

6. Select menu command Edit->paster to paste the contents of the Clipboard into the upper-left corner of the document.

7, use ALT + Drag method to copy the picture, the copied picture on the right side of the first picture.

8, repeat the 7th step two times, in the first two pictures and then paste the following two pictures.

9, close the grid line display, turn off Snap to grid options

10, select all four pictures, use the command modify->merge images. This step is necessary because the core of this technique is the use of the leather stamp tool, which can only operate on picture objects. Because all the pictures were selected before using the command, four pictures were merged into one picture.

11. Select the Rubber Stamp tool from the Toolbox

12, first of all the left and right sides of the picture between the vertical seam. Place a rubber stamp source point near the edge of a few pixels from the edge, drag from left to right over the edge (or right to left, depending on which side of the edge of the rubber stamp's source), extending the edge of one picture to the edge of the other picture.

Processing vertical seam from top to bottom, sometimes need to switch direction and source point in order to change the fuzzy operation mode, you can hold down the ALT key to reset the position of the rubber tool source point. If necessary, you can set the Rubber tool option to the softest edge in the options panel.

13. After the vertical seam is blurred, the horizontal seam is blurred by this method, and the direction of the rubber stamp is changed according to the need.

After finishing the vertical and horizontal seam blur, you should get a seamless pattern, and after this step, you can copy a part of the picture for the pattern.

25. How does fireworks use the same cutting method in different graphs?

Copy the Web layer, lock the other layer, select all copies, open another diagram, and paste it.


Contact Us

The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion; products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the content of the page makes you feel confusing, please write us an email, we will handle the problem within 5 days after receiving your email.

If you find any instances of plagiarism from the community, please send an email to: info-contact@alibabacloud.com and provide relevant evidence. A staff member will contact you within 5 working days.

A Free Trial That Lets You Build Big!

Start building with 50+ products and up to 12 months usage for Elastic Compute Service

  • Sales Support

    1 on 1 presale consultation

  • After-Sales Support

    24/7 Technical Support 6 Free Tickets per Quarter Faster Response

  • Alibaba Cloud offers highly flexible support services tailored to meet your exact needs.